RE: ich weiß mir keinen Rat mehr
Adrian Schmutzler
mail at adrianschmutzler.de
Fr Okt 9 21:33:48 CEST 2020
Hallo Steffen,
ich meinte tatsächlich auch (wie Manuel) ein Log _nachdem_ das Problem auftrat.
Die Logs nach dem Boot, die du mir geschickt hast, schauen zumindest nicht irgendwie besonders aus.
Beste Grüße
Adrian
> -----Original Message-----
> From: Steffen Winkler [mailto:freifunk at steffen-winkler.de]
> Sent: Mittwoch, 30. September 2020 14:44
> To: Adrian Schmutzler <mail at adrianschmutzler.de>
> Cc: 'freifunk in franken' <franken at freifunk.net>
> Subject: Re: ich weiß mir keinen Rat mehr
>
> Danke Adrian,
>
> nun bin ich mal wieder darauf gekommen, im folgenden die Ausgaben
>
> Grüße von Steffen
>
> root at km001:~# dmesg
> [ 0.000000] Linux version 4.14.171 (fbl at homebuild) (gcc version 7.5.0
> (OpenWrt GCC 7.5.0 r10947-65030d81f3)) #0 Thu Feb 27 21:05:12 2020
> [ 0.000000] MyLoader: sysp=6969699f, boardp=69696996, parts=69696996
> [ 0.000000] bootconsole [early0] enabled
> [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
> [ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
> [ 0.000000] Determined physical RAM map:
> [ 0.000000] memory: 08000000 @ 00000000 (usable)
> [ 0.000000] Initrd not found or empty - disabling initrd
> [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
> bytes.
> [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
> linesize 32 bytes
> [ 0.000000] Zone ranges:
> [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
> [ 0.000000] Movable zone start for each node
> [ 0.000000] Early memory node ranges
> [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
> [ 0.000000] Initmem setup node 0 [mem
> 0x0000000000000000-0x0000000007ffffff]
> [ 0.000000] On node 0 totalpages: 32768
> [ 0.000000] free_area_init_node: node 0, pgdat 804108f0, node_mem_map
> 81000020
> [ 0.000000] Normal zone: 256 pages used for memmap
> [ 0.000000] Normal zone: 0 pages reserved
> [ 0.000000] Normal zone: 32768 pages, LIFO batch:7
> [ 0.000000] random: get_random_bytes called from 0x804136ec with
> crng_init=0
> [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> [ 0.000000] pcpu-alloc: [0] 0
> [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
> [ 0.000000] Kernel command line: board=ARCHER-C7-V2
> console=ttyS0,115200 rootfstype=squashfs noinitrd
> [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
> [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536
> bytes)
> [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> [ 0.000000] Writing ErrCtl register=00000000
> [ 0.000000] Readback ErrCtl register=00000000
> [ 0.000000] Memory: 125268K/131072K available (3268K kernel code,
> 168K rwdata, 344K rodata, 244K init, 199K bss, 5804K reserved, 0K
> cma-reserved)
> [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> [ 0.000000] NR_IRQS: 51
> [ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz,
> Ref:40.000MHz
> [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 5309056796 ns
> [ 0.000008] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps
> every 5965232126ns
> [ 0.008289] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
> [ 0.074984] pid_max: default: 32768 minimum: 301
> [ 0.080081] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.087122] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
> bytes)
> [ 0.096463] clocksource: jiffies: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 19112604462750000 ns
> [ 0.106964] futex hash table entries: 256 (order: -1, 3072 bytes)
> [ 0.113835] NET: Registered protocol family 16
> [ 0.119698] MIPS: machine is TP-LINK Archer C7
> [ 0.127508] ar724x-pci ar724x-pci.0: PCIe link is down
> [ 0.133008] registering PCI controller with io_map_base unset
> [ 0.139257] registering PCI controller with io_map_base unset
> [ 0.635395] PCI host bridge to bus 0000:00
> [ 0.639801] pci_bus 0000:00: root bus resource [mem
> 0x10000000-0x11ffffff]
> [ 0.647111] pci_bus 0000:00: root bus resource [io 0x0000]
> [ 0.653048] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
> [ 0.660267] pci_bus 0000:00: No busn resource found for root bus,
> will use [bus 00-ff]
> [ 0.668718] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
> [ 0.668815] PCI host bridge to bus 0000:01
> [ 0.673171] pci_bus 0000:01: root bus resource [mem
> 0x12000000-0x13ffffff]
> [ 0.680506] pci_bus 0000:01: root bus resource [io 0x0001]
> [ 0.686432] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
> [ 0.693659] pci_bus 0000:01: No busn resource found for root bus,
> will use [bus 01-ff]
> [ 0.702113] pci 0000:01:00.0: [168c:003c] type 00 class 0x028000
> [ 0.702170] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
> [ 0.702227] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
> [ 0.702303] pci 0000:01:00.0: supports D1 D2
> [ 0.702484] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
> [ 0.702508] pci 0000:01:00.0: BAR 0: assigned [mem
> 0x12000000-0x121fffff 64bit]
> [ 0.710330] pci 0000:01:00.0: BAR 6: assigned [mem
> 0x12200000-0x1220ffff pref]
> [ 0.718552] clocksource: Switched to clocksource MIPS
> [ 0.724809] NET: Registered protocol family 2
> [ 0.730152] TCP established hash table entries: 1024 (order: 0, 4096
> bytes)
> [ 0.737579] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.744386] TCP: Hash tables configured (established 1024 bind 1024)
> [ 0.751269] UDP hash table entries: 256 (order: 0, 4096 bytes)
> [ 0.757488] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> [ 0.764378] NET: Registered protocol family 1
> [ 0.769076] PCI: CLS 0 bytes, default 32
> [ 0.773199] Crashlog allocated RAM at address 0x3f00000
> [ 0.779884] workingset: timestamp_bits=30 max_order=15 bucket_order=0
> [ 0.790922] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [ 0.797124] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
> (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
> [ 0.815540] io scheduler noop registered
> [ 0.819748] io scheduler deadline registered (default)
> [ 0.825439] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
> [ 0.832552] console [ttyS0] disabled
> [ 0.856423] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11,
> base_baud = 2500000) is a 16550A
> [ 0.865611] console [ttyS0] enabled
> [ 0.873036] bootconsole [early0] disabled
> [ 0.884822] m25p80 spi0.0: found w25q128, expected m25p80
> [ 0.901145] m25p80 spi0.0: w25q128 (16384 Kbytes)
> [ 0.906377] 5 tp-link partitions found on MTD device spi0.0
> [ 0.912058] Creating 5 MTD partitions on "spi0.0":
> [ 0.916926] 0x000000000000-0x000000020000 : "u-boot"
> [ 0.923358] 0x000000020000-0x00000015d014 : "kernel"
> [ 0.929580] 0x00000015d014-0x000000ff0000 : "rootfs"
> [ 0.935263] mtd: device 2 (rootfs) set to be root filesystem
> [ 0.941107] 1 squashfs-split partitions found on MTD device rootfs
> [ 0.947385] 0x000000400000-0x000000ff0000 : "rootfs_data"
> [ 0.955022] 0x000000ff0000-0x000001000000 : "art"
> [ 0.960951] 0x000000020000-0x000000ff0000 : "firmware"
> [ 0.968719] libphy: Fixed MDIO Bus: probed
> [ 0.983050] switch0: Atheros AR8327 rev. 4 switch registered on
> ag71xx-mdio.0
> [ 1.679739] libphy: ag71xx_mdio: probed
> [ 2.310090] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00
> [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
> [ 2.321380] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
> [ 2.598549] random: fast init done
> [ 2.950145] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: sgmii
> [ 2.957258] GACT probability on
> [ 2.960495] u32 classifier
> [ 2.963242] input device check on
> [ 2.966946] Actions configured
> [ 2.971292] NET: Registered protocol family 10
> [ 2.979831] Segment Routing with IPv6
> [ 2.983638] NET: Registered protocol family 17
> [ 2.988646] 8021q: 802.1Q VLAN Support v1.8
> [ 3.000438] VFS: Mounted root (squashfs filesystem) readonly on
> device 31:2.
> [ 3.008481] Freeing unused kernel memory: 244K
> [ 3.013036] This architecture does not have kernel memory protection.
> [ 5.176149] init: Console is alive
> [ 5.179842] init: - watchdog -
> [ 6.991351] kmodloader: loading kernel modules from /etc/modules-
> boot.d/*
> [ 7.328836] usbcore: registered new interface driver usbfs
> [ 7.334464] usbcore: registered new interface driver hub
> [ 7.339967] usbcore: registered new device driver usb
> [ 7.352649] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 7.360481] ehci-platform: EHCI generic platform driver
> [ 7.365865] ehci-platform ehci-platform.0: EHCI Host Controller
> [ 7.371945] ehci-platform ehci-platform.0: new USB bus registered,
> assigned bus number 1
> [ 7.382224] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
> [ 7.388330] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
> [ 7.418588] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
> [ 7.425811] hub 1-0:1.0: USB hub found
> [ 7.429955] hub 1-0:1.0: 1 port detected
> [ 7.434334] ehci-platform ehci-platform.1: EHCI Host Controller
> [ 7.440413] ehci-platform ehci-platform.1: new USB bus registered,
> assigned bus number 2
> [ 7.450717] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
> [ 7.456821] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
> [ 7.488630] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
> [ 7.495864] hub 2-0:1.0: USB hub found
> [ 7.500008] hub 2-0:1.0: 1 port detected
> [ 7.504941] kmodloader: done loading kernel modules from
> /etc/modules-boot.d/*
> [ 7.522677] init: - preinit -
> [ 9.324688] eth1: link up (1000Mbps/Full duplex)
> [ 9.678160] random: procd: uninitialized urandom read (4 bytes read)
> [ 13.349308] jffs2: notice: (448) jffs2_build_xattr_subsystem:
> complete building xattr subsystem, 14 of xdatum (2 unchecked, 12 orphan)
> and 27 of xref (23 dead, 0 orphan) found.
> [ 13.367505] mount_root: switching to jffs2 overlay
> [ 13.410568] overlayfs: upper fs does not support tmpfile.
> [ 13.421677] urandom-seed: Seeding with /etc/urandom.seed
> [ 13.938643] eth1: link down
> [ 13.952219] procd: - early -
> [ 13.955228] procd: - watchdog -
> [ 14.989888] procd: - watchdog -
> [ 14.993353] procd: - ubus -
> [ 15.302095] random: ubusd: uninitialized urandom read (4 bytes read)
> [ 15.308984] random: ubusd: uninitialized urandom read (4 bytes read)
> [ 15.315463] random: ubusd: uninitialized urandom read (4 bytes read)
> [ 15.323247] procd: - init -
> [ 16.811073] urandom_read: 4 callbacks suppressed
> [ 16.811080] random: jshn: uninitialized urandom read (4 bytes read)
> [ 17.117360] random: ubusd: uninitialized urandom read (4 bytes read)
> [ 17.505055] kmodloader: loading kernel modules from /etc/modules.d/*
> [ 18.010147] tun: Universal TUN/TAP device driver, 1.6
> [ 18.033741] ip6_tables: (C) 2000-2006 Netfilter Core Team
> [ 18.055188] Mirror/redirect action on
> [ 18.083110] urngd: v1.0.2 started.
> [ 18.094205] Simple TC action Loaded
> [ 18.732883] random: crng init done
> [ 19.012069] arp_tables: arp_tables: (C) 2002 David S. Miller
> [ 19.040117] Loading modules backported from Linux version
> v4.19.98-0-gd183c8e2647a
> [ 19.047795] Backport generated by backports.git v4.19.98-1-0-g8204eb99
> [ 19.095760] Ebtables v2.0 registered
> [ 19.101833] ip_tables: (C) 2000-2006 Netfilter Core Team
> [ 19.129938] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
> [ 19.214990] xt_time: kernel timezone is -0000
> [ 19.380691] pci 0000:01:00.0: using irq 41 for pin 1
> [ 19.386826] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
> [ 19.392778] ath10k_pci 0000:01:00.0: pci irq legacy oper_irq_mode 1
> irq_mode 0 reset_mode 0
> [ 19.708973] ath10k_pci 0000:01:00.0: Direct firmware load for
> ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
> [ 19.719864] ath10k_pci 0000:01:00.0: Falling back to user helper
> [ 19.873812] firmware ath10k!pre-cal-pci-0000:01:00.0.bin:
> firmware_loading_store: map pages failed
> [ 19.884429] ath10k_pci 0000:01:00.0: Direct firmware load for
> ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
> [ 19.895324] ath10k_pci 0000:01:00.0: Falling back to user helper
> [ 20.185084] firmware ath10k!QCA988X!hw2.0!firmware-6.bin:
> firmware_loading_store: map pages failed
> [ 20.197987] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c
> chip_id 0x043202ff sub 0000:0000
> [ 20.207383] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1
> tracing 0 dfs 1 testmode 1
> [ 20.220483] ath10k_pci 0000:01:00.0: firmware ver 10.2.4-1.0-00047
> api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
> [ 20.314429] ath10k_pci 0000:01:00.0: Direct firmware load for
> ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
> [ 20.325073] ath10k_pci 0000:01:00.0: Falling back to user helper
> [ 20.409537] firmware ath10k!QCA988X!hw2.0!board-2.bin:
> firmware_loading_store: map pages failed
> [ 20.418817] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A
> crc32 bebc7c08
> [ 21.516655] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2
> cal file max-sta 128 raw 0 hwcrypto 1
> [ 21.659950] ath: EEPROM regdomain: 0x0
> [ 21.659957] ath: EEPROM indicates default country code should be used
> [ 21.659961] ath: doing EEPROM country->regdmn map search
> [ 21.659973] ath: country maps to regdmn code: 0x3a
> [ 21.659978] ath: Country alpha2 being used: US
> [ 21.659981] ath: Regpair used: 0x3a
> [ 21.916207] batman_adv: B.A.T.M.A.N. advanced openwrt-2019.2-5
> (compatibility version 15) loaded
> [ 21.941304] ath: EEPROM regdomain: 0x0
> [ 21.941311] ath: EEPROM indicates default country code should be used
> [ 21.941315] ath: doing EEPROM country->regdmn map search
> [ 21.941328] ath: country maps to regdmn code: 0x3a
> [ 21.941333] ath: Country alpha2 being used: US
> [ 21.941336] ath: Regpair used: 0x3a
> [ 21.958928] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
> [ 21.960679] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000,
> irq=47
> [ 21.971486] kmodloader: done loading kernel modules from
> /etc/modules.d/*
> [ 34.460252] eth1: link up (1000Mbps/Full duplex)
> [ 34.465013] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
> [ 34.515451] br-mesh: port 1(eth1.1) entered blocking state
> [ 34.521067] br-mesh: port 1(eth1.1) entered disabled state
> [ 34.526891] device eth1.1 entered promiscuous mode
> [ 34.531803] device eth1 entered promiscuous mode
> [ 34.599713] br-mesh: port 1(eth1.1) entered blocking state
> [ 34.605286] br-mesh: port 1(eth1.1) entered forwarding state
> [ 34.611190] IPv6: ADDRCONF(NETDEV_UP): br-mesh: link is not ready
> [ 35.488613] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
> [ 35.495752] IPv6: ADDRCONF(NETDEV_CHANGE): br-mesh: link becomes
> ready
> [ 37.339949] 8021q: adding VLAN 0 to HW filter on device bat0
> [ 37.346312] br-mesh: port 2(bat0) entered blocking state
> [ 37.351765] br-mesh: port 2(bat0) entered disabled state
> [ 37.357396] device bat0 entered promiscuous mode
> [ 37.362265] br-mesh: port 2(bat0) entered blocking state
> [ 37.367658] br-mesh: port 2(bat0) entered forwarding state
> [ 37.838635] batman_adv: bat0: No IGMP Querier present - multicast
> optimizations disabled
> [ 37.846849] batman_adv: bat0: No MLD Querier present - multicast
> optimizations disabled
> [ 38.362714] batman_adv: bat0: Adding interface: eth1.3
> [ 38.367939] batman_adv: bat0: The MTU of interface eth1.3 is too
> small (1500) to handle the transport of batman-adv packets. Packets
> going over this interface will be fragmented on layer2 which could
> impact the performance. Setting the MTU to 1560 would solve the problem.
> [ 38.392405] batman_adv: bat0: Interface activated: eth1.3
> [ 44.240865] br-mesh: port 2(bat0) entered disabled state
> [ 44.246325] br-mesh: port 1(eth1.1) entered disabled state
> [ 44.268346] batman_adv: bat0: Interface deactivated: eth1.3
> [ 44.274066] batman_adv: bat0: Removing interface: eth1.3
> [ 44.297255] device bat0 left promiscuous mode
> [ 44.301826] br-mesh: port 2(bat0) entered disabled state
> [ 44.338866] device eth1.1 left promiscuous mode
> [ 44.343596] br-mesh: port 1(eth1.1) entered disabled state
> [ 44.369569] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
> [ 44.390262] device eth1 left promiscuous mode
> [ 44.917973] eth1: link down
> [ 48.865237] eth1: link up (1000Mbps/Full duplex)
> [ 48.870057] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
> [ 48.897003] br-mesh: port 1(eth1.1) entered blocking state
> [ 48.902617] br-mesh: port 1(eth1.1) entered disabled state
> [ 48.908446] device eth1.1 entered promiscuous mode
> [ 48.913352] device eth1 entered promiscuous mode
> [ 48.968717] br-mesh: port 1(eth1.1) entered blocking state
> [ 48.974296] br-mesh: port 1(eth1.1) entered forwarding state
> [ 48.980219] IPv6: ADDRCONF(NETDEV_UP): br-mesh: link is not ready
> [ 50.119880] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
> [ 50.127038] IPv6: ADDRCONF(NETDEV_CHANGE): br-mesh: link becomes
> ready
> [ 50.590705] 8021q: adding VLAN 0 to HW filter on device bat0
> [ 50.598321] br-mesh: port 2(bat0) entered blocking state
> [ 50.603773] br-mesh: port 2(bat0) entered disabled state
> [ 50.609441] device bat0 entered promiscuous mode
> [ 50.614262] br-mesh: port 2(bat0) entered blocking state
> [ 50.619694] br-mesh: port 2(bat0) entered forwarding state
> [ 51.088750] batman_adv: bat0: No IGMP Querier present - multicast
> optimizations disabled
> [ 51.096964] batman_adv: bat0: No MLD Querier present - multicast
> optimizations disabled
> [ 51.222742] batman_adv: bat0: Adding interface: eth1.3
> [ 51.227968] batman_adv: bat0: The MTU of interface eth1.3 is too
> small (1500) to handle the transport of batman-adv packets. Packets
> going over this interface will be fragmented on layer2 which could
> impact the performance. Setting the MTU to 1560 would solve the problem.
> [ 51.252435] batman_adv: bat0: Interface activated: eth1.3
> [ 58.985872] batman_adv: bat0: Adding interface: fffVPN
> [ 58.991229] batman_adv: bat0: The MTU of interface fffVPN is too
> small (1426) to handle the transport of batman-adv packets. Packets
> going over this interface will be fragmented on layer2 which could
> impact the performance. Setting the MTU to 1560 would solve the problem.
> [ 59.015663] batman_adv: bat0: Interface activated: fffVPN
> root at km001:~#
>
> root at km001:~# logread
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.000000] Linux version
> 4.14.171 (fbl at homebuild) (gcc version 7.5.0 (OpenWrt GCC 7.5.0
> r10947-65030d81f3)) #0 Thu Feb 27 21:05:12 2020
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.000000] MyLoader:
> sysp=6969699f, boardp=69696996, parts=69696996
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] bootconsole
> [early0] enabled
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] CPU0 revision
> is: 00019750 (MIPS 74Kc)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] SoC: Qualcomm
> Atheros QCA9558 ver 1 rev 0
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Determined
> physical RAM map:
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] memory: 08000000
> @ 00000000 (usable)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Initrd not
> found or empty - disabling initrd
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 0.000000] Primary
> instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 0.000000] Primary data
> cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Zone ranges:
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Normal [mem
> 0x0000000000000000-0x0000000007ffffff]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Movable zone
> start for each node
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Early memory
> node ranges
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] node 0: [mem
> 0x0000000000000000-0x0000000007ffffff]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Initmem setup
> node 0 [mem 0x0000000000000000-0x0000000007ffffff]
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.000000] On node 0
> totalpages: 32768
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.000000]
> free_area_init_node: node 0, pgdat 804108f0, node_mem_map 81000020
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.000000] Normal zone:
> 256 pages used for memmap
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.000000] Normal zone: 0
> pages reserved
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.000000] Normal zone:
> 32768 pages, LIFO batch:7
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.000000] random:
> get_random_bytes called from 0x804136ec with crng_init=0
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.000000] pcpu-alloc: s0
> r0 d32768 u32768 alloc=1*32768
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Built 1
> zonelists, mobility grouping on. Total pages: 32512
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.000000] Kernel command
> line: board=ARCHER-C7-V2 console=ttyS0,115200 rootfstype=squashfs
> noinitrd
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] PID hash table
> entries: 512 (order: -1, 2048 bytes)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Dentry cache
> hash table entries: 16384 (order: 4, 65536 bytes)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Inode-cache
> hash table entries: 8192 (order: 3, 32768 bytes)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Writing ErrCtl
> register=00000000
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Readback
> ErrCtl register=00000000
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Memory:
> 125268K/131072K available (3268K kernel code, 168K rwdata, 344K rodata,
> 244K init, 199K bss, 5804K reserved, 0K cma-reserved)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] SLUB:
> HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] NR_IRQS: 51
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] Clocks:
> CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000000] clocksource:
> MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.000008] sched_clock:
> 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.008289] Calibrating
> delay loop... 358.80 BogoMIPS (lpj=1794048)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.074984] pid_max:
> default: 32768 minimum: 301
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.080081] Mount-cache
> hash table entries: 1024 (order: 0, 4096 bytes)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.087122]
> Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.096463] clocksource:
> jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns:
> 19112604462750000 ns
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.106964] futex hash
> table entries: 256 (order: -1, 3072 bytes)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.113835] NET:
> Registered protocol family 16
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.119698] MIPS: machine
> is TP-LINK Archer C7
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 0.127508] ar724x-pci
> ar724x-pci.0: PCIe link is down
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 0.133008] registering
> PCI controller with io_map_base unset
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 0.139257] registering
> PCI controller with io_map_base unset
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.635395] PCI host
> bridge to bus 0000:00
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.639801] pci_bus
> 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.647111] pci_bus
> 0000:00: root bus resource [io 0x0000]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.653048] pci_bus
> 0000:00: root bus resource [??? 0x00000000 flags 0x0]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.660267] pci_bus
> 0000:00: No busn resource found for root bus, will use [bus 00-ff]
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.668718] pci_bus 0000:00:
> busn_res: [bus 00-ff] end is updated to 00
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.668815] PCI host
> bridge to bus 0000:01
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.673171] pci_bus
> 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.680506] pci_bus
> 0000:01: root bus resource [io 0x0001]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.686432] pci_bus
> 0000:01: root bus resource [??? 0x00000000 flags 0x0]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.693659] pci_bus
> 0000:01: No busn resource found for root bus, will use [bus 01-ff]
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.702113] pci
> 0000:01:00.0: [168c:003c] type 00 class 0x028000
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.702170] pci
> 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.702227] pci
> 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.702303] pci
> 0000:01:00.0: supports D1 D2
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.702484] pci_bus 0000:01:
> busn_res: [bus 01-ff] end is updated to 01
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.702508] pci
> 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.710330] pci
> 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.718552] clocksource:
> Switched to clocksource MIPS
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.724809] NET:
> Registered protocol family 2
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.730152] TCP
> established hash table entries: 1024 (order: 0, 4096 bytes)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.737579] TCP bind hash
> table entries: 1024 (order: 0, 4096 bytes)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.744386] TCP: Hash
> tables configured (established 1024 bind 1024)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.751269] UDP hash table
> entries: 256 (order: 0, 4096 bytes)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.757488] UDP-Lite hash
> table entries: 256 (order: 0, 4096 bytes)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.764378] NET:
> Registered protocol family 1
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 0.769076] PCI: CLS 0
> bytes, default 32
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 0.773199] Crashlog
> allocated RAM at address 0x3f00000
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.779884] workingset:
> timestamp_bits=30 max_order=15 bucket_order=0
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.790922] squashfs:
> version 4.0 (2009/01/31) Phillip Lougher
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.797124] jffs2: version
> 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006
> Red
> Hat, Inc.
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.815540] io scheduler
> noop registered
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.819748] io scheduler
> deadline registered (default)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.825439] Serial:
> 8250/16550 driver, 1 ports, IRQ sharing disabled
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.832552] console
> [ttyS0] disabled
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.856423] serial8250.0:
> ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.865611] console
> [ttyS0] enabled
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.873036] bootconsole
> [early0] disabled
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 0.884822] m25p80 spi0.0:
> found w25q128, expected m25p80
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.901145] m25p80 spi0.0:
> w25q128 (16384 Kbytes)
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.906377] 5 tp-link
> partitions found on MTD device spi0.0
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.912058] Creating 5 MTD
> partitions on "spi0.0":
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.916926]
> 0x000000000000-0x000000020000 : "u-boot"
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.923358]
> 0x000000020000-0x00000015d014 : "kernel"
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.929580]
> 0x00000015d014-0x000000ff0000 : "rootfs"
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.935263] mtd: device 2
> (rootfs) set to be root filesystem
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.941107] 1
> squashfs-split partitions found on MTD device rootfs
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.947385]
> 0x000000400000-0x000000ff0000 : "rootfs_data"
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.955022]
> 0x000000ff0000-0x000001000000 : "art"
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 0.960951]
> 0x000000020000-0x000000ff0000 : "firmware"
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.968719] libphy: Fixed
> MDIO Bus: probed
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 0.983050] switch0:
> Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 1.679739] libphy:
> ag71xx_mdio: probed
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.310090] ag71xx
> ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034,
> driver=Atheros AR8216/AR8236/AR8316]
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.321380] eth0: Atheros
> AG71xx at 0xb9000000, irq 4, mode: rgmii
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 2.598549] random: fast
> init done
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.950145] eth1: Atheros
> AG71xx at 0xba000000, irq 5, mode: sgmii
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.957258] GACT
> probability on
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.960495] u32 classifier
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.963242] input device
> check on
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.966946] Actions
> configured
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.971292] NET:
> Registered protocol family 10
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.979831] Segment
> Routing with IPv6
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.983638] NET:
> Registered protocol family 17
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 2.988646] 8021q: 802.1Q
> VLAN Support v1.8
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 3.000438] VFS: Mounted
> root (squashfs filesystem) readonly on device 31:2.
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 3.008481] Freeing unused
> kernel memory: 244K
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 3.013036] This
> architecture does not have kernel memory protection.
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 5.176149] init: Console
> is alive
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 5.179842] init: - watchdog -
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 6.991351] kmodloader:
> loading kernel modules from /etc/modules-boot.d/*
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.328836] usbcore:
> registered new interface driver usbfs
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.334464] usbcore:
> registered new interface driver hub
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.339967] usbcore:
> registered new device driver usb
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.352649] ehci_hcd: USB
> 2.0 'Enhanced' Host Controller (EHCI) Driver
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.360481] ehci-platform:
> EHCI generic platform driver
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.365865] ehci-platform
> ehci-platform.0: EHCI Host Controller
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.371945] ehci-platform
> ehci-platform.0: new USB bus registered, assigned bus number 1
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.382224] ehci-platform
> ehci-platform.0: TX-TX IDP fix enabled
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.388330] ehci-platform
> ehci-platform.0: irq 48, io mem 0x1b000000
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.418588] ehci-platform
> ehci-platform.0: USB 2.0 started, EHCI 1.00
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.425811] hub 1-0:1.0:
> USB hub found
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.429955] hub 1-0:1.0: 1
> port detected
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.434334] ehci-platform
> ehci-platform.1: EHCI Host Controller
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.440413] ehci-platform
> ehci-platform.1: new USB bus registered, assigned bus number 2
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.450717] ehci-platform
> ehci-platform.1: TX-TX IDP fix enabled
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.456821] ehci-platform
> ehci-platform.1: irq 49, io mem 0x1b400000
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.488630] ehci-platform
> ehci-platform.1: USB 2.0 started, EHCI 1.00
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.495864] hub 2-0:1.0:
> USB hub found
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 7.500008] hub 2-0:1.0: 1
> port detected
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 7.504941] kmodloader:
> done loading kernel modules from /etc/modules-boot.d/*
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 7.522677] init: - preinit -
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 9.324688] eth1: link up
> (1000Mbps/Full duplex)
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 9.678160] random: procd:
> uninitialized urandom read (4 bytes read)
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 13.349308] jffs2: notice:
> (448) jffs2_build_xattr_subsystem: complete building xattr subsystem, 14
> of xdatum (2 unchecked, 12 orphan) and 27 of xref (23 dead, 0 orphan)
> found.
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 13.367505] mount_root:
> switching to jffs2 overlay
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 13.410568] overlayfs:
> upper fs does not support tmpfile.
> Mon Sep 21 10:10:28 2020 user.warn kernel: [ 13.421677] urandom-seed:
> Seeding with /etc/urandom.seed
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 13.938643] eth1: link down
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 13.952219] procd: - early -
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 13.955228] procd: -
> watchdog -
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 14.989888] procd: -
> watchdog -
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 14.993353] procd: - ubus -
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 15.302095] random: ubusd:
> uninitialized urandom read (4 bytes read)
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 15.308984] random: ubusd:
> uninitialized urandom read (4 bytes read)
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 15.315463] random: ubusd:
> uninitialized urandom read (4 bytes read)
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 15.323247] procd: - init -
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 16.811073] urandom_read:
> 4 callbacks suppressed
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 16.811080] random: jshn:
> uninitialized urandom read (4 bytes read)
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 17.117360] random: ubusd:
> uninitialized urandom read (4 bytes read)
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 17.505055] kmodloader:
> loading kernel modules from /etc/modules.d/*
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 18.010147] tun: Universal
> TUN/TAP device driver, 1.6
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 18.033741] ip6_tables:
> (C) 2000-2006 Netfilter Core Team
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 18.055188]
> Mirror/redirect action on
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 18.083110] urngd: v1.0.2
> started.
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 18.094205] Simple TC
> action Loaded
> Mon Sep 21 10:10:28 2020 kern.notice kernel: [ 18.732883] random: crng
> init done
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 19.012069] arp_tables:
> arp_tables: (C) 2002 David S. Miller
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 19.040117] Loading
> modules backported from Linux version v4.19.98-0-gd183c8e2647a
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 19.047795] Backport
> generated by backports.git v4.19.98-1-0-g8204eb99
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 19.095760] Ebtables v2.0
> registered
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 19.101833] ip_tables: (C)
> 2000-2006 Netfilter Core Team
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 19.129938] nf_conntrack
> version 0.5.0 (2048 buckets, 8192 max)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 19.214990] xt_time:
> kernel timezone is -0000
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 19.380691] pci
> 0000:01:00.0: using irq 41 for pin 1
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 19.386826] PCI: Enabling
> device 0000:01:00.0 (0000 -> 0002)
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 19.392778] ath10k_pci
> 0000:01:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 19.708973] ath10k_pci
> 0000:01:00.0: Direct firmware load for
> ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 19.719864] ath10k_pci
> 0000:01:00.0: Falling back to user helper
> Mon Sep 21 10:10:28 2020 kern.err kernel: [ 19.873812] firmware
> ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages
> failed
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 19.884429] ath10k_pci
> 0000:01:00.0: Direct firmware load for
> ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 19.895324] ath10k_pci
> 0000:01:00.0: Falling back to user helper
> Mon Sep 21 10:10:28 2020 kern.err kernel: [ 20.185084] firmware
> ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages
> failed
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 20.197987] ath10k_pci
> 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub
> 0000:0000
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 20.207383] ath10k_pci
> 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 20.220483] ath10k_pci
> 0000:01:00.0: firmware ver 10.2.4-1.0-00047 api 5 features
> no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 20.314429] ath10k_pci
> 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin
> failed with error -2
> Mon Sep 21 10:10:28 2020 kern.warn kernel: [ 20.325073] ath10k_pci
> 0000:01:00.0: Falling back to user helper
> Mon Sep 21 10:10:28 2020 kern.err kernel: [ 20.409537] firmware
> ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages
> failed
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 20.418817] ath10k_pci
> 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 21.516655] ath10k_pci
> 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0
> hwcrypto 1
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.659950] ath: EEPROM
> regdomain: 0x0
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.659957] ath: EEPROM
> indicates default country code should be used
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.659961] ath: doing
> EEPROM country->regdmn map search
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.659973] ath: country
> maps to regdmn code: 0x3a
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.659978] ath: Country
> alpha2 being used: US
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.659981] ath: Regpair
> used: 0x3a
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 21.916207] batman_adv:
> B.A.T.M.A.N. advanced openwrt-2019.2-5 (compatibility version 15) loaded
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.941304] ath: EEPROM
> regdomain: 0x0
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.941311] ath: EEPROM
> indicates default country code should be used
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.941315] ath: doing
> EEPROM country->regdmn map search
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.941328] ath: country
> maps to regdmn code: 0x3a
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.941333] ath: Country
> alpha2 being used: US
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.941336] ath: Regpair
> used: 0x3a
> Mon Sep 21 10:10:28 2020 kern.debug kernel: [ 21.958928] ieee80211 phy1:
> Selected rate control algorithm 'minstrel_ht'
> Mon Sep 21 10:10:28 2020 kern.info kernel: [ 21.960679] ieee80211
> phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
> Mon Sep 21 10:10:28 2020 user.info kernel: [ 21.971486] kmodloader:
> done loading kernel modules from /etc/modules.d/*
> Mon Sep 21 10:10:29 2020 authpriv.info dropbear[958]: Not backgrounding
> Mon Sep 21 10:10:31 2020 user.notice : Added device handler type: 8021ad
> Mon Sep 21 10:10:31 2020 user.notice : Added device handler type: 8021q
> Mon Sep 21 10:10:31 2020 user.notice : Added device handler type: macvlan
> Mon Sep 21 10:10:31 2020 user.notice : Added device handler type: veth
> Mon Sep 21 10:10:31 2020 user.notice : Added device handler type: bridge
> Mon Sep 21 10:10:31 2020 user.notice : Added device handler type:
> Network device
> Mon Sep 21 10:10:31 2020 user.notice : Added device handler type: tunnel
> Mon Sep 21 10:10:31 2020 daemon.notice procd: /etc/init.d/network:
> 'radio0' is disabled
> Mon Sep 21 10:10:31 2020 daemon.notice procd: /etc/init.d/network:
> 'radio1' is disabled
> Mon Sep 21 10:10:31 2020 daemon.notice procd: /etc/init.d/network:
> 'radio0' is disabled
> Mon Sep 21 10:10:31 2020 daemon.notice procd: /etc/init.d/network:
> 'radio1' is disabled
> Mon Sep 21 10:10:37 2020 daemon.warn netifd: You have delegated
> IPv6-prefixes but haven't assigned them to any interface. Did you forget
> to set option ip6assign on your lan-interfaces?
> Mon Sep 21 10:10:37 2020 kern.info kernel: [ 34.460252] eth1: link up
> (1000Mbps/Full duplex)
> Mon Sep 21 10:10:37 2020 kern.info kernel: [ 34.465013] IPv6:
> ADDRCONF(NETDEV_UP): eth1: link is not ready
> Mon Sep 21 10:10:37 2020 kern.info kernel: [ 34.515451] br-mesh: port
> 1(eth1.1) entered blocking state
> Mon Sep 21 10:10:37 2020 kern.info kernel: [ 34.521067] br-mesh: port
> 1(eth1.1) entered disabled state
> Mon Sep 21 10:10:37 2020 kern.info kernel: [ 34.526891] device eth1.1
> entered promiscuous mode
> Mon Sep 21 10:10:37 2020 kern.info kernel: [ 34.531803] device eth1
> entered promiscuous mode
> Mon Sep 21 10:10:37 2020 kern.info kernel: [ 34.599713] br-mesh: port
> 1(eth1.1) entered blocking state
> Mon Sep 21 10:10:37 2020 kern.info kernel: [ 34.605286] br-mesh: port
> 1(eth1.1) entered forwarding state
> Mon Sep 21 10:10:37 2020 kern.info kernel: [ 34.611190] IPv6:
> ADDRCONF(NETDEV_UP): br-mesh: link is not ready
> Mon Sep 21 10:10:37 2020 daemon.notice netifd: Interface 'mesh' is enabled
> Mon Sep 21 10:10:37 2020 daemon.notice netifd: Interface 'mesh' is
> setting up now
> Mon Sep 21 10:10:37 2020 daemon.notice netifd: Interface 'mesh' is now up
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'bat0' is
> setting up now
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'ethmesh' is
> enabled
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'loopback' is
> enabled
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'loopback' is
> setting up now
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'loopback' is
> now up
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'wan' is enabled
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: bridge 'br-mesh' link is up
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'mesh' has link
> connectivity
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Network device 'eth1'
> link is up
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: VLAN 'eth1.1' link is up
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: VLAN 'eth1.3' link is up
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'ethmesh' has
> link connectivity
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'ethmesh' is
> setting up now
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Network device 'lo' link
> is up
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'loopback' has
> link connectivity
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: VLAN 'eth1.2' link is up
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'wan' has link
> connectivity
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: Interface 'wan' is
> setting up now
> Mon Sep 21 10:10:38 2020 kern.info kernel: [ 35.488613] IPv6:
> ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
> Mon Sep 21 10:10:38 2020 kern.info kernel: [ 35.495752] IPv6:
> ADDRCONF(NETDEV_CHANGE): br-mesh: link becomes ready
> Mon Sep 21 10:10:38 2020 daemon.notice netifd: wan (1204): udhcpc:
> started, v1.30.1
> Mon Sep 21 10:10:39 2020 user.notice sysctl:
> net.ipv6.conf.eth1.2.accept_ra = 1
> Mon Sep 21 10:10:39 2020 user.notice sysctl:
> net.ipv6.conf.eth1.2.accept_ra_defrtr = 1
> Mon Sep 21 10:10:39 2020 user.notice sysctl:
> net.ipv6.conf.eth1.2.accept_ra_pinfo = 1
> Mon Sep 21 10:10:39 2020 user.notice sysctl:
> net.ipv6.conf.eth1.2.autoconf = 1
> Mon Sep 21 10:10:39 2020 user.notice sysctl:
> net.ipv6.conf.eth1.2.forwarding = 0
> Mon Sep 21 10:10:39 2020 daemon.notice netifd: ethmesh (1187): Error -
> failed to find batman-adv interface: No such device
> Mon Sep 21 10:10:39 2020 daemon.notice netifd: Interface 'ethmesh' is
> now down
> Mon Sep 21 10:10:39 2020 daemon.notice netifd: Interface 'ethmesh' is
> disabled
> Mon Sep 21 10:10:39 2020 daemon.notice netifd: VLAN 'eth1.3' link is down
> Mon Sep 21 10:10:39 2020 daemon.notice netifd: Interface 'ethmesh' has
> link connectivity loss
> Mon Sep 21 10:10:39 2020 daemon.notice netifd: wan (1204): udhcpc:
> sending discover
> Mon Sep 21 10:10:40 2020 kern.info kernel: [ 37.339949] 8021q: adding
> VLAN 0 to HW filter on device bat0
> Mon Sep 21 10:10:40 2020 kern.info kernel: [ 37.346312] br-mesh: port
> 2(bat0) entered blocking state
> Mon Sep 21 10:10:40 2020 kern.info kernel: [ 37.351765] br-mesh: port
> 2(bat0) entered disabled state
> Mon Sep 21 10:10:40 2020 kern.info kernel: [ 37.357396] device bat0
> entered promiscuous mode
> Mon Sep 21 10:10:40 2020 kern.info kernel: [ 37.362265] br-mesh: port
> 2(bat0) entered blocking state
> Mon Sep 21 10:10:40 2020 kern.info kernel: [ 37.367658] br-mesh: port
> 2(bat0) entered forwarding state
> Mon Sep 21 10:10:40 2020 daemon.notice netifd: Network device 'bat0'
> link is up
> Mon Sep 21 10:10:40 2020 daemon.notice netifd: Interface 'ethmesh' is
> enabled
> Mon Sep 21 10:10:40 2020 daemon.notice netifd: Interface 'bat0' is now up
> Mon Sep 21 10:10:40 2020 daemon.notice netifd: VLAN 'eth1.3' link is up
> Mon Sep 21 10:10:40 2020 daemon.notice netifd: Interface 'ethmesh' has
> link connectivity
> Mon Sep 21 10:10:40 2020 daemon.notice netifd: Interface 'ethmesh' is
> setting up now
> Mon Sep 21 10:10:40 2020 kern.info kernel: [ 37.838635] batman_adv:
> bat0: No IGMP Querier present - multicast optimizations disabled
> Mon Sep 21 10:10:40 2020 kern.info kernel: [ 37.846849] batman_adv:
> bat0: No MLD Querier present - multicast optimizations disabled
> Mon Sep 21 10:10:40 2020 daemon.info procd: Not starting instance
> fff-uradvd::data, command not set
> Mon Sep 21 10:10:41 2020 kern.info kernel: [ 38.362714] batman_adv:
> bat0: Adding interface: eth1.3
> Mon Sep 21 10:10:41 2020 kern.info kernel: [ 38.367939] batman_adv:
> bat0: The MTU of interface eth1.3 is too small (1500) to handle the
> transport of batman-adv packets. Packets going over this interface will
> be fragmented on layer2 which could impact the performance. Setting the
> MTU to 1560 would solve the problem.
> Mon Sep 21 10:10:41 2020 kern.info kernel: [ 38.392405] batman_adv:
> bat0: Interface activated: eth1.3
> Mon Sep 21 10:10:41 2020 daemon.notice netifd: Interface 'ethmesh' is now
> up
> Mon Sep 21 10:10:43 2020 daemon.notice netifd: wan (1204): udhcpc:
> sending select for 192.168.0.177
> Mon Sep 21 10:10:43 2020 daemon.notice netifd: wan (1204): udhcpc: lease
> of 192.168.0.177 obtained, lease time 3600
> Mon Sep 21 10:10:44 2020 daemon.notice netifd: Interface 'wan' is now up
> Mon Sep 21 10:10:46 2020 daemon.notice procd: /etc/rc.d/S95done:
> 'radio0' is disabled
> Mon Sep 21 10:10:46 2020 daemon.notice procd: /etc/rc.d/S95done:
> 'radio1' is disabled
> Mon Sep 21 10:10:46 2020 daemon.notice netifd: Interface 'ethmesh' has
> lost the connection
> Mon Sep 21 10:10:46 2020 daemon.notice netifd: Interface 'loopback' is
> now down
> Mon Sep 21 10:10:46 2020 daemon.notice netifd: Interface 'loopback' is
> disabled
> Mon Sep 21 10:10:46 2020 daemon.notice netifd: Network device 'lo' link
> is down
> Mon Sep 21 10:10:46 2020 daemon.notice netifd: Interface 'loopback' has
> link connectivity loss
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Interface 'mesh' is now
> down
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.240865] br-mesh: port
> 2(bat0) entered disabled state
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.246325] br-mesh: port
> 1(eth1.1) entered disabled state
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.268346] batman_adv:
> bat0: Interface deactivated: eth1.3
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.274066] batman_adv:
> bat0: Removing interface: eth1.3
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.297255] device bat0
> left promiscuous mode
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.301826] br-mesh: port
> 2(bat0) entered disabled state
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.338866] device eth1.1
> left promiscuous mode
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.343596] br-mesh: port
> 1(eth1.1) entered disabled state
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.369569] IPv6:
> ADDRCONF(NETDEV_UP): eth1.1: link is not ready
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Interface 'mesh' is disabled
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Interface 'ethmesh' is
> now down
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.390262] device eth1
> left promiscuous mode
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Interface 'ethmesh' is
> disabled
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Interface 'bat0' is now
> down
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Network device 'bat0'
> link is down
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: VLAN 'eth1.1' link is down
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: bridge 'br-mesh' link is
> down
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Interface 'mesh' has link
> connectivity loss
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: VLAN 'eth1.3' link is down
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Interface 'ethmesh' has
> link connectivity loss
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: wan (1204): udhcpc:
> received SIGTERM
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Interface 'wan' is now down
> Mon Sep 21 10:10:47 2020 kern.info kernel: [ 44.917973] eth1: link down
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Interface 'wan' is disabled
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: VLAN 'eth1.2' link is down
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Interface 'wan' has link
> connectivity loss
> Mon Sep 21 10:10:47 2020 daemon.notice netifd: Network device 'eth1'
> link is down
> Mon Sep 21 10:10:49 2020 user.notice : Added device handler type: 8021ad
> Mon Sep 21 10:10:49 2020 user.notice : Added device handler type: 8021q
> Mon Sep 21 10:10:49 2020 user.notice : Added device handler type: macvlan
> Mon Sep 21 10:10:49 2020 user.notice : Added device handler type: veth
> Mon Sep 21 10:10:49 2020 user.notice : Added device handler type: bridge
> Mon Sep 21 10:10:49 2020 user.notice : Added device handler type:
> Network device
> Mon Sep 21 10:10:49 2020 user.notice : Added device handler type: tunnel
> Mon Sep 21 10:10:49 2020 daemon.notice procd: /etc/rc.d/S95done:
> 18:d6:c7:fc:d7:68
> Mon Sep 21 10:10:49 2020 daemon.notice procd: /etc/rc.d/S95done: MAC for
> ethmesh is set already
> Mon Sep 21 10:10:49 2020 daemon.notice procd: /etc/rc.d/S95done:
> 18:d6:c7:fc:d7:67
> Mon Sep 21 10:10:49 2020 daemon.notice procd: /etc/rc.d/S95done: MAC for
> mesh is set already
> Mon Sep 21 10:10:49 2020 daemon.notice procd: /etc/rc.d/S95done: IPv6
> for mesh is set already
> Mon Sep 21 10:10:49 2020 daemon.notice procd: /etc/init.d/network:
> 'radio0' is disabled
> Mon Sep 21 10:10:49 2020 daemon.notice procd: /etc/init.d/network:
> 'radio1' is disabled
> Mon Sep 21 10:10:49 2020 daemon.notice procd: /etc/init.d/network:
> 'radio0' is disabled
> Mon Sep 21 10:10:49 2020 daemon.notice procd: /etc/init.d/network:
> 'radio1' is disabled
> Mon Sep 21 10:10:51 2020 daemon.warn netifd: You have delegated
> IPv6-prefixes but haven't assigned them to any interface. Did you forget
> to set option ip6assign on your lan-interfaces?
> Mon Sep 21 10:10:51 2020 kern.info kernel: [ 48.865237] eth1: link up
> (1000Mbps/Full duplex)
> Mon Sep 21 10:10:51 2020 kern.info kernel: [ 48.870057] IPv6:
> ADDRCONF(NETDEV_UP): eth1: link is not ready
> Mon Sep 21 10:10:51 2020 kern.info kernel: [ 48.897003] br-mesh: port
> 1(eth1.1) entered blocking state
> Mon Sep 21 10:10:51 2020 kern.info kernel: [ 48.902617] br-mesh: port
> 1(eth1.1) entered disabled state
> Mon Sep 21 10:10:51 2020 kern.info kernel: [ 48.908446] device eth1.1
> entered promiscuous mode
> Mon Sep 21 10:10:51 2020 kern.info kernel: [ 48.913352] device eth1
> entered promiscuous mode
> Mon Sep 21 10:10:51 2020 kern.info kernel: [ 48.968717] br-mesh: port
> 1(eth1.1) entered blocking state
> Mon Sep 21 10:10:51 2020 kern.info kernel: [ 48.974296] br-mesh: port
> 1(eth1.1) entered forwarding state
> Mon Sep 21 10:10:51 2020 kern.info kernel: [ 48.980219] IPv6:
> ADDRCONF(NETDEV_UP): br-mesh: link is not ready
> Mon Sep 21 10:10:51 2020 daemon.notice netifd: Interface 'mesh' is enabled
> Mon Sep 21 10:10:51 2020 daemon.notice netifd: Interface 'mesh' is
> setting up now
> Mon Sep 21 10:10:51 2020 daemon.notice netifd: Interface 'mesh' is now up
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'bat0' is
> setting up now
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'ethmesh' is
> enabled
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'loopback' is
> enabled
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'loopback' is
> setting up now
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'loopback' is
> now up
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'wan' is enabled
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: bridge 'br-mesh' link is up
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'mesh' has link
> connectivity
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Network device 'eth1'
> link is up
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: VLAN 'eth1.1' link is up
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: VLAN 'eth1.3' link is up
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'ethmesh' has
> link connectivity
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'ethmesh' is
> setting up now
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Network device 'lo' link
> is up
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'loopback' has
> link connectivity
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: VLAN 'eth1.2' link is up
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'wan' has link
> connectivity
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: Interface 'wan' is
> setting up now
> Mon Sep 21 10:10:52 2020 kern.info kernel: [ 50.119880] IPv6:
> ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
> Mon Sep 21 10:10:52 2020 kern.info kernel: [ 50.127038] IPv6:
> ADDRCONF(NETDEV_CHANGE): br-mesh: link becomes ready
> Mon Sep 21 10:10:52 2020 daemon.notice netifd: wan (1833): udhcpc:
> started, v1.30.1
> Mon Sep 21 10:10:53 2020 user.notice sysctl:
> net.ipv6.conf.eth1.2.accept_ra = 1
> Mon Sep 21 10:10:53 2020 user.notice sysctl:
> net.ipv6.conf.eth1.2.accept_ra_defrtr = 1
> Mon Sep 21 10:10:53 2020 user.notice sysctl:
> net.ipv6.conf.eth1.2.accept_ra_pinfo = 1
> Mon Sep 21 10:10:53 2020 user.notice sysctl:
> net.ipv6.conf.eth1.2.autoconf = 1
> Mon Sep 21 10:10:53 2020 user.notice sysctl:
> net.ipv6.conf.eth1.2.forwarding = 0
> Mon Sep 21 10:10:53 2020 daemon.notice netifd: wan (1833): udhcpc:
> sending discover
> Mon Sep 21 10:10:53 2020 daemon.notice netifd: wan (1833): udhcpc:
> sending select for 192.168.0.177
> Mon Sep 21 10:10:53 2020 daemon.notice netifd: wan (1833): udhcpc: lease
> of 192.168.0.177 obtained, lease time 3600
> Mon Sep 21 10:10:53 2020 kern.info kernel: [ 50.590705] 8021q: adding
> VLAN 0 to HW filter on device bat0
> Mon Sep 21 10:10:53 2020 kern.info kernel: [ 50.598321] br-mesh: port
> 2(bat0) entered blocking state
> Mon Sep 21 10:10:53 2020 kern.info kernel: [ 50.603773] br-mesh: port
> 2(bat0) entered disabled state
> Mon Sep 21 10:10:53 2020 kern.info kernel: [ 50.609441] device bat0
> entered promiscuous mode
> Mon Sep 21 10:10:53 2020 kern.info kernel: [ 50.614262] br-mesh: port
> 2(bat0) entered blocking state
> Mon Sep 21 10:10:53 2020 kern.info kernel: [ 50.619694] br-mesh: port
> 2(bat0) entered forwarding state
> Mon Sep 21 10:10:53 2020 daemon.notice netifd: Network device 'bat0'
> link is up
> Mon Sep 21 10:10:53 2020 daemon.notice netifd: Interface 'bat0' is now up
> Mon Sep 21 10:10:53 2020 daemon.notice netifd: Interface 'ethmesh' is
> now down
> Mon Sep 21 10:10:53 2020 daemon.notice netifd: Interface 'ethmesh' is
> disabled
> Mon Sep 21 10:10:53 2020 daemon.notice netifd: Interface 'ethmesh' is
> enabled
> Mon Sep 21 10:10:53 2020 daemon.notice netifd: Interface 'ethmesh' is
> setting up now
> Mon Sep 21 10:10:53 2020 daemon.notice netifd: Interface 'wan' is now up
> Mon Sep 21 10:10:53 2020 kern.info kernel: [ 51.088750] batman_adv:
> bat0: No IGMP Querier present - multicast optimizations disabled
> Mon Sep 21 10:10:53 2020 kern.info kernel: [ 51.096964] batman_adv:
> bat0: No MLD Querier present - multicast optimizations disabled
> Mon Sep 21 10:10:54 2020 kern.info kernel: [ 51.222742] batman_adv:
> bat0: Adding interface: eth1.3
> Mon Sep 21 10:10:54 2020 kern.info kernel: [ 51.227968] batman_adv:
> bat0: The MTU of interface eth1.3 is too small (1500) to handle the
> transport of batman-adv packets. Packets going over this interface will
> be fragmented on layer2 which could impact the performance. Setting the
> MTU to 1560 would solve the problem.
> Mon Sep 21 10:10:54 2020 kern.info kernel: [ 51.252435] batman_adv:
> bat0: Interface activated: eth1.3
> Mon Sep 21 10:10:54 2020 daemon.notice netifd: Interface 'ethmesh' is now
> up
> Mon Sep 21 10:10:57 2020 daemon.notice procd: /etc/rc.d/S95done: Getting
> hoodfile from Keyserver
> Mon Sep 21 10:10:57 2020 daemon.notice procd: /etc/rc.d/S95done:
> Connecting to keyserver.freifunk-franken.de (193.192.41.2:80)
> Mon Sep 21 10:10:57 2020 daemon.notice procd: /etc/rc.d/S95done: New
> file detected, we reconfigure the Node
> Mon Sep 21 10:10:57 2020 daemon.notice procd: /etc/rc.d/S95done: Setting
> hood name: Roettenbach (ID 42)
> Mon Sep 21 10:10:57 2020 daemon.notice procd: /etc/rc.d/S95done:
> Reloading wifi
> Mon Sep 21 10:10:57 2020 daemon.notice procd: /etc/rc.d/S95done:
> Command
> failed: Not found
> Mon Sep 21 10:10:57 2020 daemon.notice procd: /etc/rc.d/S95done: waiting
> 30 secs for br-mesh address...
> Mon Sep 21 10:11:00 2020 daemon.notice procd: /etc/rc.d/S95done: rm:
> can't remove '/tmp/fastd_fff_peers/*': No such file or directory
> Mon Sep 21 10:11:01 2020 kern.info kernel: [ 58.985872] batman_adv:
> bat0: Adding interface: fffVPN
> Mon Sep 21 10:11:01 2020 kern.info kernel: [ 58.991229] batman_adv:
> bat0: The MTU of interface fffVPN is too small (1426) to handle the
> transport of batman-adv packets. Packets going over this interface will
> be fragmented on layer2 which could impact the performance. Setting the
> MTU to 1560 would solve the problem.
> Mon Sep 21 10:11:01 2020 kern.info kernel: [ 59.015663] batman_adv:
> bat0: Interface activated: fffVPN
> Mon Sep 21 10:11:01 2020 daemon.notice procd: /etc/rc.d/S95done: Set ULA
> address to br-mesh: fd43:5602:29bd:8b::18d6:c7fc:d767/64
> Mon Sep 21 10:11:01 2020 daemon.notice procd: /etc/rc.d/S95done: Set ULA
> EUI-64 address to br-mesh: fd43:5602:29bd:8b:1ad6:c7ff:fefc:d767/64
> Mon Sep 21 10:11:02 2020 daemon.notice procd: /etc/rc.d/S95done: Set ULA
> route to br-mesh.
> Mon Sep 21 10:11:02 2020 daemon.notice procd: /etc/rc.d/S96led: setting
> up led USB1
> Mon Sep 21 10:11:02 2020 daemon.notice procd: /etc/rc.d/S96led: setting
> up led USB2
> Mon Sep 21 10:11:02 2020 daemon.notice procd: /etc/rc.d/S96led: setting
> up led WLAN2G
> Mon Sep 21 10:11:02 2020 daemon.notice procd: /etc/rc.d/S96led: setting
> up led WLAN5G
> Mon Sep 21 10:11:03 2020 daemon.notice procd: /etc/rc.d/S99alfred:
> waiting 30 secs for br-mesh address...
> Mon Sep 21 10:11:03 2020 daemon.notice procd: /etc/rc.d/S99macnock: {
> "name": "macnock", "script": "\/etc\/rc.d\/S99macnock", "instances": {
> "macnock": { "command": [ "\/usr\/sbin\/macnock", "eth1.3",
> "Roettenbach" ], "respawn": [ "10", "10", "0" ], "file": [
> "\/etc\/config\/system" ], "netdev": [ "eth1.3" ], "stdout": true,
> "stderr": true, "user": "root" } }, "triggers": [ [ "config.change", [
> "if", [ "eq", "package", "system" ], [ "run_script",
> "\/etc\/init.d\/macnock", "reload" ] ], 1000 ], [ "interface.*", [ "if",
> [ "eq", "interface", "ethmesh" ], [ "run_script",
> "\/etc\/init.d\/macnock", "reload" ] ], 1000 ] ], "validate": [ ],
> "data": { } }
> Mon Sep 21 10:11:04 2020 daemon.info macnock[2407]: /usr/sbin/macnock:
> Running for hood Roettenbach on interface eth1.3
> Mon Sep 21 10:11:04 2020 daemon.info macnock[2407]: [t] Removing old
> qdisc.
> Mon Sep 21 10:11:04 2020 daemon.info procd: - init complete -
> Mon Sep 21 10:11:05 2020 daemon.err macnock[2407]: RTNETLINK answers:
> No
> such file or directory
> Mon Sep 21 10:11:05 2020 daemon.info macnock[2407]: [t] Adding qdisc.
> Mon Sep 21 10:11:05 2020 daemon.info macnock[2407]: [t] Blocking all
> batman-adv traffic.
> Mon Sep 21 10:11:06 2020 daemon.info macnock[2407]: [m] new entry:
> 18:d6:c7:fc:d7:68.
> Mon Sep 21 10:13:15 2020 daemon.info micrond[1406]: Getting hoodfile
> from Keyserver
> Mon Sep 21 10:13:15 2020 daemon.err micrond[1406]: Connecting to
> keyserver.freifunk-franken.de (193.192.41.2:80)
> Mon Sep 21 10:13:15 2020 daemon.info micrond[1406]: We have no new file.
> We do nothing. We try it again in 5 minutes...
> Mon Sep 21 10:13:17 2020 daemon.info micrond[1406]: Set ULA address to
> br-mesh: fd43:5602:29bd:8b::18d6:c7fc:d767/64
> Mon Sep 21 10:13:17 2020 daemon.info micrond[1406]: Address already set.
> Mon Sep 21 10:13:17 2020 daemon.info micrond[1406]: Route already set.
> Mon Sep 21 10:15:10 2020 daemon.err micrond[1406]: nodewatcher:
> Generate
> actual status data
> Mon Sep 21 10:15:10 2020 daemon.err micrond[1406]: nodewatcher: Putting
> all information into a XML-File and save it at /tmp/crawldata/node.data
> Mon Sep 21 10:15:11 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting basic system status data
> Mon Sep 21 10:15:11 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting version information
> Mon Sep 21 10:15:11 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting hood information and additional status data
> Mon Sep 21 10:15:11 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from network interfaces
> Mon Sep 21 10:15:12 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from batman advanced and its interfaces
> Mon Sep 21 10:15:12 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information about connected clients
> Mon Sep 21 10:18:17 2020 daemon.info micrond[1406]: Getting hoodfile
> from Keyserver
> Mon Sep 21 10:18:17 2020 daemon.err micrond[1406]: Connecting to
> keyserver.freifunk-franken.de (193.192.41.2:80)
> Mon Sep 21 10:18:17 2020 daemon.info micrond[1406]: We have no new file.
> We do nothing. We try it again in 5 minutes...
> Mon Sep 21 10:18:20 2020 daemon.info micrond[1406]: Set ULA address to
> br-mesh: fd43:5602:29bd:8b::18d6:c7fc:d767/64
> Mon Sep 21 10:18:20 2020 daemon.info micrond[1406]: Address already set.
> Mon Sep 21 10:18:20 2020 daemon.info micrond[1406]: Route already set.
> Mon Sep 21 10:20:12 2020 daemon.err micrond[1406]: nodewatcher:
> Generate
> actual status data
> Mon Sep 21 10:20:12 2020 daemon.err micrond[1406]: nodewatcher: Putting
> all information into a XML-File and save it at /tmp/crawldata/node.data
> Mon Sep 21 10:20:12 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting basic system status data
> Mon Sep 21 10:20:12 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting version information
> Mon Sep 21 10:20:12 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting hood information and additional status data
> Mon Sep 21 10:20:12 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from network interfaces
> Mon Sep 21 10:20:13 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from batman advanced and its interfaces
> Mon Sep 21 10:20:13 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information about connected clients
> Mon Sep 21 10:23:07 2020 daemon.info micrond[1406]: Getting hoodfile
> from Keyserver
> Mon Sep 21 10:23:07 2020 daemon.err micrond[1406]: Connecting to
> keyserver.freifunk-franken.de (193.192.41.2:80)
> Mon Sep 21 10:23:08 2020 daemon.info micrond[1406]: We have no new file.
> We do nothing. We try it again in 5 minutes...
> Mon Sep 21 10:23:10 2020 daemon.info micrond[1406]: Set ULA address to
> br-mesh: fd43:5602:29bd:8b::18d6:c7fc:d767/64
> Mon Sep 21 10:23:10 2020 daemon.info micrond[1406]: Address already set.
> Mon Sep 21 10:23:10 2020 daemon.info micrond[1406]: Route already set.
> Mon Sep 21 10:25:19 2020 daemon.err micrond[1406]: nodewatcher:
> Generate
> actual status data
> Mon Sep 21 10:25:19 2020 daemon.err micrond[1406]: nodewatcher: Putting
> all information into a XML-File and save it at /tmp/crawldata/node.data
> Mon Sep 21 10:25:19 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting basic system status data
> Mon Sep 21 10:25:19 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting version information
> Mon Sep 21 10:25:19 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting hood information and additional status data
> Mon Sep 21 10:25:19 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from network interfaces
> Mon Sep 21 10:25:20 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from batman advanced and its interfaces
> Mon Sep 21 10:25:20 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information about connected clients
> Mon Sep 21 10:28:12 2020 daemon.info micrond[1406]: Getting hoodfile
> from Keyserver
> Mon Sep 21 10:28:12 2020 daemon.err micrond[1406]: Connecting to
> keyserver.freifunk-franken.de (193.192.41.2:80)
> Mon Sep 21 10:28:12 2020 daemon.info micrond[1406]: We have no new file.
> We do nothing. We try it again in 5 minutes...
> Mon Sep 21 10:28:15 2020 daemon.info micrond[1406]: Set ULA address to
> br-mesh: fd43:5602:29bd:8b::18d6:c7fc:d767/64
> Mon Sep 21 10:28:15 2020 daemon.info micrond[1406]: Address already set.
> Mon Sep 21 10:28:15 2020 daemon.info micrond[1406]: Route already set.
> Mon Sep 21 10:30:08 2020 daemon.err micrond[1406]: nodewatcher:
> Generate
> actual status data
> Mon Sep 21 10:30:08 2020 daemon.err micrond[1406]: nodewatcher: Putting
> all information into a XML-File and save it at /tmp/crawldata/node.data
> Mon Sep 21 10:30:08 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting basic system status data
> Mon Sep 21 10:30:08 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting version information
> Mon Sep 21 10:30:08 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting hood information and additional status data
> Mon Sep 21 10:30:08 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from network interfaces
> Mon Sep 21 10:30:09 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from batman advanced and its interfaces
> Mon Sep 21 10:30:09 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information about connected clients
> Mon Sep 21 10:33:05 2020 daemon.info micrond[1406]: Getting hoodfile
> from Keyserver
> Mon Sep 21 10:33:05 2020 daemon.err micrond[1406]: Connecting to
> keyserver.freifunk-franken.de (193.192.41.2:80)
> Mon Sep 21 10:33:06 2020 daemon.info micrond[1406]: We have no new file.
> We do nothing. We try it again in 5 minutes...
> Mon Sep 21 10:33:08 2020 daemon.info micrond[1406]: Set ULA address to
> br-mesh: fd43:5602:29bd:8b::18d6:c7fc:d767/64
> Mon Sep 21 10:33:08 2020 daemon.info micrond[1406]: Address already set.
> Mon Sep 21 10:33:08 2020 daemon.info micrond[1406]: Route already set.
> Mon Sep 21 10:33:32 2020 authpriv.info dropbear[4059]: Child connection
> from fd43:5602:29bd:76:586e:1463:2d07:7828:58401
> Mon Sep 21 10:33:43 2020 authpriv.notice dropbear[4059]: Password auth
> succeeded for 'root' from fd43:5602:29bd:76:586e:1463:2d07:7828:58401
> Mon Sep 21 10:35:22 2020 daemon.err micrond[1406]: nodewatcher:
> Generate
> actual status data
> Mon Sep 21 10:35:22 2020 daemon.err micrond[1406]: nodewatcher: Putting
> all information into a XML-File and save it at /tmp/crawldata/node.data
> Mon Sep 21 10:35:22 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting basic system status data
> Mon Sep 21 10:35:22 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting version information
> Mon Sep 21 10:35:22 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting hood information and additional status data
> Mon Sep 21 10:35:22 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from network interfaces
> Mon Sep 21 10:35:23 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from batman advanced and its interfaces
> Mon Sep 21 10:35:23 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information about connected clients
> Mon Sep 21 10:38:04 2020 daemon.info micrond[1406]: Getting hoodfile
> from Keyserver
> Mon Sep 21 10:38:04 2020 daemon.err micrond[1406]: Connecting to
> keyserver.freifunk-franken.de (193.192.41.2:80)
> Mon Sep 21 10:38:04 2020 daemon.info micrond[1406]: We have no new file.
> We do nothing. We try it again in 5 minutes...
> Mon Sep 21 10:38:07 2020 daemon.info micrond[1406]: Set ULA address to
> br-mesh: fd43:5602:29bd:8b::18d6:c7fc:d767/64
> Mon Sep 21 10:38:07 2020 daemon.info micrond[1406]: Address already set.
> Mon Sep 21 10:38:07 2020 daemon.info micrond[1406]: Route already set.
> Mon Sep 21 10:40:08 2020 daemon.err micrond[1406]: nodewatcher:
> Generate
> actual status data
> Mon Sep 21 10:40:08 2020 daemon.err micrond[1406]: nodewatcher: Putting
> all information into a XML-File and save it at /tmp/crawldata/node.data
> Mon Sep 21 10:40:08 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting basic system status data
> Mon Sep 21 10:40:08 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting version information
> Mon Sep 21 10:40:08 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting hood information and additional status data
> Mon Sep 21 10:40:08 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from network interfaces
> Mon Sep 21 10:40:09 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information from batman advanced and its interfaces
> Mon Sep 21 10:40:09 2020 daemon.err micrond[1406]: nodewatcher:
> Collecting information about connected clients
> Mon Sep 21 10:40:53 2020 daemon.notice netifd: wan (1833): udhcpc:
> sending renew to 192.168.0.1
> Mon Sep 21 10:40:53 2020 daemon.notice netifd: wan (1833): udhcpc: lease
> of 192.168.0.177 obtained, lease time 3600
> root at km001:~#
>
> Am 28.09.2020 um 12:39 schrieb Adrian Schmutzler:
> > Was steht denn so im Log?
> >
> > dmesg and logread?
> >
> > Grüße
> >
> > Adrian
> >
> >> -----Original Message-----
> >> From: franken [mailto:franken-bounces at freifunk.net] On Behalf Of
> Steffen
> >> Winkler
> >> Sent: Montag, 28. September 2020 10:11
> >> To: freifunk in franken <franken at freifunk.net>
> >> Subject: ich weiß mir keinen Rat mehr
> >>
> >> Hallo zusammen,
> >>
> >> ich weiß mir keinen Rat mehr, siehe:
> >> https://monitoring.freifunk-franken.de/routers/16600
> >>
> >> Regelmäßig gehen da die Router offline und kommen nicht wieder hoch.
> Der
> >> Kabel-Anschluss von Vodafone wurde auch schon geprüft, passt alles. Wir
> >> haben Batman mittlerweile per Kabel erweitert. Die Installation habe ich
> vom
> >> Ludwig Mieth geerbt, waren erst alles 841er. Habe nun schon den Router
> >> getauscht, der am WAN hängt aber das ändert nichts.
> >>
> >> Grüße von Steffen
-------------- nächster Teil --------------
Ein Dateianhang mit Binärdaten wurde abgetrennt...
Dateiname : openpgp-digital-signature.asc
Dateityp : application/pgp-signature
Dateigröße : 834 bytes
Beschreibung: nicht verfügbar
URL : <https://lists.freifunk.net/pipermail/franken-freifunk.net/attachments/20201009/2cf20b56/attachment-0001.sig>
Mehr Informationen über die Mailingliste franken