[PATCH v3 03/14] fff-network: Reorganize network initialization

robert rlanghammer at web.de
Mi Apr 24 09:47:31 CEST 2019


Reviewed-by: Robert Langhammer <rlanghammer at web.de>

Am 23.04.19 um 13:07 schrieb Adrian Schmutzler:
> Hallo zusammen,
>
> ich bräuchte noch folgende Reviews:
> Robert 3/14
> Christian 6/14
> Christian 14/14
>
> Folgende Änderungen habe ich jetzt berücksichtigt (ich will nicht nochmal ein Patchset schicken):
> - default-case für Ports wie in Mail enthalten.
> - sleep 5 weg
> - etc/init.d/network restart weg bei Skripten, dafür Hinweis bei echo ("Port updated successfully. Please restart network or device!")
> - 90-firstbootfff von fff-support nach fff-network verschoben
>
> Der CPUPORT-Patch hat zwar auch nur ein Review, das wäre mir aber wurscht, da der im Moment ja noch keine Abhängigkeiten hat.
>
> Grüße
>
> Adrian
>
>> -----Original Message-----
>> From: franken-dev [mailto:franken-dev-bounces at freifunk.net] On Behalf Of
>> Adrian Schmutzler
>> Sent: Montag, 22. April 2019 14:35
>> To: franken-dev at freifunk.net
>> Subject: [PATCH v3 03/14] fff-network: Reorganize network initialization
>>
>> This removes the configurenetwork script and replaces it by some
>> scripts run only during first boot.
>>
>> This introduces several changes:
>> - The different tasks dealt with in configurenetwork are split.
>>   Thus, one script deals with switch/port setup, one with br-mesh
>>   MAC address, one with ETHMESHMAC, and one with IP addresses.
>>   This makes the whole approach more modular, compared to the
>>   monolithic configurenetwork.
>> - Where configurenetwork contained sophisticated, nested conditions
>>   to account for all possible combinations of variables, the new
>>   approach is inspired by OpenWrt's board.d subfiles. Instead of
>>   defining variables, we now directly call function in a
>>   select-case. This is much more flexible, as we can just put code
>>   there for a special case instead of bending configurenetwork for
>>   it.
>> - The select-case accounts for the various cases of similar/same
>>   parameters of multiple devices, which can be grouped now.
>> - Scripts are run only at first boot. Later changes have to be
>>   done manually (we will provide some scripts later). Those will
>>   typically be limited to changing only the ports; no need to run
>>   whole network config again.
>> - network.mode and network.config will disappear. For switch-based
>>   devices, there is no advantage of using network.config compared
>>   directly editing /etc/config/network. Upgrade-safety can be
>>   established by putting uci commands in an upgrade-safe script
>>   file (to be provided in a later patch).
>>
>> After this patch, show_info and the ports display in WebUI are
>> broken. Those will be fixed in a later patch.
>>
>> Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>
>>
>> ---
>>
>> Changed in v2:
>> - Fixed archer-c60-v2 to v1
>> - Added network functions file in uci-defaults/22c
>> - Removed some -q from uci
>> - Removed all commands only needed for running devices (this is
>>   uci only)
>> - Added descriptions for functions in networksetup
>>
>> Changed in v3:
>> - Changed order of 22a and 22b
>> - uci del instead uci set for WAN on one-port
>> - switch/vlanX instead of eth#/eth#.# for switch-based devices
>> ---
>>  bsp/default/root_file_system/etc/rc.local          |   4 -
>>  src/packages/fff/fff-network/Makefile              |   4 +-
>>  .../files/etc/uci-defaults/22a-config-ports        |  89 +++++++
>>  .../files/etc/uci-defaults/22b-config-routermac    |  55 +++++
>>  .../files/etc/uci-defaults/22c-config-ethmesh      |  75 ++++++
>>  .../files/etc/uci-defaults/23-config-ipaddr        |  31 +++
>>  .../files/lib/functions/fff/networksetup           | 163 +++++++++++++
>>  .../fff-network/files/lib/functions/fff/portorder  |  31 +++
>>  .../fff-network/files/usr/sbin/configurenetwork    | 263
>> ---------------------
>>  src/packages/fff/fff-sysupgrade/Makefile           |   3 +-
>>  .../files/etc/uci-defaults/99-fff-sysupgrade       |   1 -
>>  11 files changed, 446 insertions(+), 273 deletions(-)
>>  create mode 100644
>> src/packages/fff/fff-network/files/etc/uci-defaults/22a-config-ports
>>  create mode 100644
>> src/packages/fff/fff-network/files/etc/uci-defaults/22b-config-routermac
>>  create mode 100644
>> src/packages/fff/fff-network/files/etc/uci-defaults/22c-config-ethmesh
>>  create mode 100644
>> src/packages/fff/fff-network/files/etc/uci-defaults/23-config-ipaddr
>>  create mode 100644
>> src/packages/fff/fff-network/files/lib/functions/fff/networksetup
>>  create mode 100644
>> src/packages/fff/fff-network/files/lib/functions/fff/portorder
>>  delete mode 100755
>> src/packages/fff/fff-network/files/usr/sbin/configurenetwork
>>
>> diff --git a/bsp/default/root_file_system/etc/rc.local
>> b/bsp/default/root_file_system/etc/rc.local
>> index 59042c37..e02368a5 100755
>> --- a/bsp/default/root_file_system/etc/rc.local
>> +++ b/bsp/default/root_file_system/etc/rc.local
>> @@ -2,10 +2,6 @@
>>  # Put your custom commands here that should be executed once
>>  # the system init finished. By default this file does nothing.
>>
>> -/usr/sbin/configurenetwork
>> -
>> -sleep 3
>> -
>>  /usr/sbin/configurehood
>>
>>  touch /tmp/started
>> diff --git a/src/packages/fff/fff-network/Makefile
>> b/src/packages/fff/fff-network/Makefile
>> index e9335884..11796797 100644
>> --- a/src/packages/fff/fff-network/Makefile
>> +++ b/src/packages/fff/fff-network/Makefile
>> @@ -1,8 +1,7 @@
>>  include $(TOPDIR)/rules.mk
>>
>>  PKG_NAME:=fff-network
>> -PKG_VERSION:=10
>> -PKG_RELEASE:=1
>> +PKG_RELEASE:=11
>>
>>  PKG_BUILD_DIR:=$(BUILD_DIR)/$(PKG_NAME)
>>
>> @@ -34,7 +33,6 @@ endef
>>
>>  define Package/$(PKG_NAME)/install
>>  	$(CP) ./files/* $(1)/
>> -	test -d ./$(BOARD) && $(CP) ./$(BOARD)/* $(1)/etc/
>>  endef
>>
>>  $(eval $(call BuildPackage,$(PKG_NAME)))
>> diff --git
>> a/src/packages/fff/fff-network/files/etc/uci-defaults/22a-config-ports
>> b/src/packages/fff/fff-network/files/etc/uci-defaults/22a-config-ports
>> new file mode 100644
>> index 00000000..b8eaceab
>> --- /dev/null
>> +++ b/src/packages/fff/fff-network/files/etc/uci-defaults/22a-config-ports
>> @@ -0,0 +1,89 @@
>> +#!/bin/sh
>> +# Copyright 2019 Adrian Schmutzler
>> +# License GPLv3
>> +
>> +BOARD="$(uci get board.model.name)"
>> +
>> +. /lib/functions/fff/networksetup
>> +
>> +case "$BOARD" in
>> +	archer-c7-v2)
>> +		setupSwitch "eth1" "4 5 0t" "2 3 0t" "1 6"
>> +		setupWan "eth0"
>> +		;;
>> +	archer-c25-v1|\
>> +	archer-c60-v1)
>> +		setupSwitch "eth1" "1 2 0t" "3 4 0t"
>> +		setupWan "eth0"
>> +		;;
>> +	cpe210|\
>> +	cpe510)
>> +		# Default: LAN0: WAN, LAN1: CLIENT
>> +		setupSwitch "eth0" "0t 4" "0t" "0t 5"
>> +		setupWan "eth0.2"
>> +		;;
>> +	gl-ar150)
>> +		# Default: CLIENT
>> +		setupSwitch "eth1" "0t 1" "0t"
>> +		setupWan "eth0"
>> +		;;
>> +	tl-wdr3500-v1|\
>> +	tl-wr741nd-v2|\
>> +	tl-wr841-v7|\
>> +	tl-wr841-v9|\
>> +	tl-wr841-v10|\
>> +	tl-wr841-v11|\
>> +	tl-wr841-v12)
>> +		setupSwitch "eth0" "1 2 0t" "3 4 0t"
>> +		setupWan "eth1"
>> +		;;
>> +	tl-wdr3600-v1|\
>> +	tl-wdr4300-v1|\
>> +	tl-wdr4310-v1|\
>> +	tl-wdr4900-v1)
>> +		setupSwitch "eth0" "4 5 0t" "2 3 0t" "1 0t"
>> +		setupWan "eth0.2"
>> +		;;
>> +	tl-wr841-v8|\
>> +	tl-wr842n-v2)
>> +		setupSwitch "eth1" "1 4 0t" "2 3 0t"
>> +		setupWan "eth0"
>> +		;;
>> +	tl-wr740n-v4|\
>> +	tl-wr740nd-v4|\
>> +	tl-wr741nd-v4)
>> +		setupSwitch "eth0" "1 4 0t" "2 3 0t"
>> +		setupWan "eth1"
>> +		;;
>> +	tl-wr1043nd-v1)
>> +		setupSwitch "eth0" "3 4 5t" "1 2 5t" "0 5t"
>> +		setupWan "eth0.2"
>> +		;;
>> +	tl-wr1043nd-v2|\
>> +	tl-wr1043nd-v3)
>> +		setupSwitch "eth0" "1 2 6t" "3 4 6t" "5 6t"
>> +		setupWan "eth0.2"
>> +		;;
>> +	tl-wr1043nd-v4|\
>> +	tl-wr1043n-v5)
>> +		setupSwitch "eth0" "1 2 0t" "3 4 0t" "5 0t"
>> +		setupWan "eth0.2"
>> +		;;
>> +	cpe210-v2|\
>> +	cpe210-v3|\
>> +	tl-mr3020-v1|\
>> +	tl-wa850re-v1|\
>> +	tl-wa860re-v1|\
>> +	tl-wa901nd-v2|\
>> +	ubnt-bullet-m|\
>> +	ubnt-loco-m|\
>> +	ubnt-loco-m-xw|\
>> +	ubnt-nano-m|\
>> +	ubnt-pico-m|\
>> +	ubnt-power-m-xw|\
>> +	ubnt-unifi|\
>> +	ubnt-unifiac-lite|\
>> +	ubnt-unifiac-mesh)
>> +		setupOnePort "eth0" "CLIENT"
>> +		;;
>> +esac
>> diff --git
>> a/src/packages/fff/fff-network/files/etc/uci-defaults/22b-config-routermac
>> b/src/packages/fff/fff-network/files/etc/uci-defaults/22b-config-routermac
>> new file mode 100644
>> index 00000000..d1a5e50c
>> --- /dev/null
>> +++
>> b/src/packages/fff/fff-network/files/etc/uci-defaults/22b-config-routermac
>> @@ -0,0 +1,55 @@
>> +#!/bin/sh
>> +# Copyright 2019 Adrian Schmutzler
>> +# License GPLv3
>> +
>> +BOARD="$(uci get board.model.name)"
>> +
>> +. /lib/functions/fff/networksetup
>> +
>> +. /lib/functions.sh
>> +. /lib/functions/system.sh
>> +
>> +case "$BOARD" in
>> +	archer-c7-v2|\
>> +	tl-wr841-v8|\
>> +	tl-wr842n-v2|\
>> +	tl-wr1043nd-v2|\
>> +	tl-wr1043nd-v3)
>> +		ROUTERMAC=$(cat /sys/class/net/eth1/address)
>> +		;;
>> +	cpe210-v2|\
>> +	cpe210-v3|\
>> +	tl-wa850re-v1|\
>> +	tl-wa860re-v1|\
>> +	tl-wa901nd-v2|\
>> +	tl-wdr3500-v1|\
>> +	tl-wr740n-v4|\
>> +	tl-wr740nd-v4|\
>> +	tl-wr741nd-v2|\
>> +	tl-wr741nd-v4|\
>> +	tl-wr841-v7|\
>> +	ubnt-bullet-m|\
>> +	ubnt-loco-m|\
>> +	ubnt-loco-m-xw|\
>> +	ubnt-nano-m|\
>> +	ubnt-pico-m|\
>> +	ubnt-power-m-xw|\
>> +	ubnt-unifi)
>> +		ROUTERMAC=$(cat /sys/class/ieee80211/phy0/macaddress)
>> +		;;
>> +	tl-wdr3600-v1|\
>> +	tl-wdr4300-v1|\
>> +	tl-wdr4310-v1)
>> +		ROUTERMAC=$(cat /sys/class/ieee80211/phy1/macaddress)
>> +		;;
>> +	ubnt-unifiac-lite|\
>> +	ubnt-unifiac-mesh)
>> +		ROUTERMAC=$(mtd_get_mac_binary EEPROM 0x0)
>> +		;;
>> +	*)
>> +		ROUTERMAC=$(cat /sys/class/net/eth0/address)
>> +		;;
>> +esac
>> +
>> +uci set "network.mesh.macaddr=$ROUTERMAC"
>> +uci commit network
>> diff --git
>> a/src/packages/fff/fff-network/files/etc/uci-defaults/22c-config-ethmesh
>> b/src/packages/fff/fff-network/files/etc/uci-defaults/22c-config-ethmesh
>> new file mode 100644
>> index 00000000..86c840c3
>> --- /dev/null
>> +++
>> b/src/packages/fff/fff-network/files/etc/uci-defaults/22c-config-ethmesh
>> @@ -0,0 +1,75 @@
>> +#!/bin/sh
>> +# Copyright 2019 Adrian Schmutzler
>> +# License GPLv3
>> +
>> +BOARD="$(uci get board.model.name)"
>> +
>> +. /lib/functions/fff/network
>> +. /lib/functions/fff/networksetup
>> +
>> +. /lib/functions.sh
>> +. /lib/functions/system.sh
>> +
>> +# macFlipLocalBit:
>> +# use mac address from phyX with 'locally administered' bit set to '1'
>> +# only possible, because wXmesh is created first and therefore gets the
>> 'universally administered address'
>> +
>> +case "$BOARD" in
>> +	archer-c7-v2|\
>> +	tl-wr841-v8|\
>> +	tl-wr842n-v2)
>> +		ETHMESHMAC=$(cat /sys/class/net/eth0/address)
>> +		;;
>> +	archer-c25-v1|\
>> +	archer-c60-v1|\
>> +	tl-wr740n-v4|\
>> +	tl-wr740nd-v4|\
>> +	tl-wr741nd-v2|\
>> +	tl-wr741nd-v4|\
>> +	tl-wr841-v7|\
>> +	tl-wr841-v9|\
>> +	tl-wr841-v10|\
>> +	tl-wr841-v11|\
>> +	tl-wr841-v12)
>> +		ETHMESHMAC=$(cat /sys/class/net/eth1/address)
>> +		;;
>> +	cpe210|\
>> +	cpe210-v2|\
>> +	cpe210-v3|\
>> +	cpe510|\
>> +	tl-wa850re-v1|\
>> +	tl-wa860re-v1|\
>> +	tl-wa901nd-v2|\
>> +	tl-wr1043nd-v1|\
>> +	ubnt-bullet-m|\
>> +	ubnt-loco-m|\
>> +	ubnt-loco-m-xw|\
>> +	ubnt-nano-m|\
>> +	ubnt-pico-m|\
>> +	ubnt-power-m-xw|\
>> +	ubnt-unifi)
>> +		ETHMESHMAC=$(macFlipLocalBit "$(cat
>> /sys/class/ieee80211/phy0/macaddress)")
>> +		;;
>> +	gl-ar150|\
>> +	tl-mr3020-v1)
>> +		ETHMESHMAC=$(macFlipLocalBit "$(cat
>> /sys/class/net/eth0/address)")
>> +		;;
>> +	tl-wdr4900-v1)
>> +		ETHMESHMAC=$(macFlipLocalBit "$(cat
>> /sys/class/ieee80211/phy1/macaddress)")
>> +		;;
>> +	tl-wr1043nd-v4)
>> +		ETHMESHMAC=$(mtd_get_mac_binary config 0x1017c)
>> +		;;
>> +	tl-wr1043n-v5)
>> +		ETHMESHMAC=$(macaddr_add $(mtd_get_mac_binary
>> product-info
>> 8) 1)
>> +		;;
>> +	ubnt-unifiac-lite|\
>> +	ubnt-unifiac-mesh)
>> +		ETHMESHMAC=$(macFlipLocalBit "$(mtd_get_mac_binary
>> EEPROM
>> 0x0)")
>> +		;;
>> +esac
>> +
>> +if [ -n "$ETHMESHMAC" ]; then
>> +	uci set "network.ethmesh.macaddr=$ETHMESHMAC"
>> +	uci commit network
>> +fi
>> diff --git
>> a/src/packages/fff/fff-network/files/etc/uci-defaults/23-config-ipaddr
>> b/src/packages/fff/fff-network/files/etc/uci-defaults/23-config-ipaddr
>> new file mode 100644
>> index 00000000..db500c15
>> --- /dev/null
>> +++ b/src/packages/fff/fff-network/files/etc/uci-defaults/23-config-ipaddr
>> @@ -0,0 +1,31 @@
>> +#!/bin/sh
>> +# Copyright 2019 Adrian Schmutzler
>> +# License GPLv3
>> +
>> +. /lib/functions/fff/network
>> +
>> +echo "Setting IPv6 addresses"
>> +# Some time needed :(
>> +sleep 5
>> +
>> +ROUTERMAC=$(uci get network.mesh.macaddr)
>> +prefix="fdff:0::/64"
>> +
>> +# Set $prefix as prefix
>> +uci set network.globals=globals
>> +uci set "network.globals.ula_prefix=$prefix"
>> +
>> +# Set $prefix::MAC as IP
>> +addr="$(ipMacAssemble "$prefix" "$ROUTERMAC")"
>> +uci add_list "network.mesh.ip6addr=$addr"
>> +uci set network.mesh.proto=static
>> +
>> +# Set $prefix::1 as IP
>> +addr="$(ipAssemble "$prefix" "1")"
>> +uci add_list "network.mesh.ip6addr=$addr"
>> +
>> +# Set $prefix::link-local as IP
>> +addr="$(ipEUIAssemble "$prefix" "$ROUTERMAC")"
>> +uci add_list "network.mesh.ip6addr=$addr"
>> +
>> +uci commit network
>> diff --git
>> a/src/packages/fff/fff-network/files/lib/functions/fff/networksetup
>> b/src/packages/fff/fff-network/files/lib/functions/fff/networksetup
>> new file mode 100644
>> index 00000000..ccc943df
>> --- /dev/null
>> +++ b/src/packages/fff/fff-network/files/lib/functions/fff/networksetup
>> @@ -0,0 +1,163 @@
>> +# Copyright 2019 Adrian Schmutzler
>> +# License GPLv3
>> +
>> +. /lib/functions/network.sh
>> +
>> +setAutoConf() {
>> +	# Sets ipv6 auto configuration on an interface to on/off
>> +	# Usage: setAutoConf <interface> <[0|1]>
>> +	local iface=$1
>> +	local on=$2
>> +
>> +	sysctlfile="/etc/sysctl.d/51-fff-network-$iface.conf"
>> +	echo "# Generated from configurenetwork" > "$sysctlfile"
>> +	echo "net.ipv6.conf.$iface.accept_ra = $on" >> "$sysctlfile"
>> +	echo "net.ipv6.conf.$iface.accept_ra_defrtr = $on" >>
>> "$sysctlfile"
>> +	echo "net.ipv6.conf.$iface.accept_ra_pinfo = $on" >> "$sysctlfile"
>> +	echo "net.ipv6.conf.$iface.autoconf = $on" >> "$sysctlfile"
>> +	echo "net.ipv6.conf.$iface.accept_ra_rtr_pref = $on" >>
>> "$sysctlfile"
>> +	echo "net.ipv6.conf.$iface.forwarding = 0" >> "$sysctlfile"
>> +
>> +	/sbin/sysctl -p "$sysctlfile"
>> +}
>> +
>> +enableAutoConf() {
>> +	# Enables ipv6 auto configuration on an interface
>> +	# Usage: enableAutoConf <interface>
>> +	local iface=$1
>> +
>> +	setAutoConf "$iface" "1"
>> +}
>> +
>> +disableAutoConf() {
>> +	# Disables ipv6 auto configuration on an interface
>> +	# Usage: disableAutoConf <interface>
>> +	local iface=$1
>> +
>> +	setAutoConf "$iface" "0"
>> +}
>> +
>> +fixMac() {
>> +	# Update MAC address on live device/interface
>> +	#
>> +	# fixMac <newmac> <interface>
>> +	#
>> +	# newmac: MAC address to be set
>> +	# interface: Interface to be updated as in uci (e.g. mesh)
>> +
>> +	local newmac=$1
>> +	local iface=$2
>> +	local dev
>> +
>> +	echo "Fixing MAC on $iface"
>> +	sleep 10
>> +
>> +	network_get_physdev dev "$iface"
>> +
>> +	uci set "network.${iface}.macaddr=$newmac"
>> +	uci commit network
>> +
>> +	if [ -n "$dev" ]; then
>> +		ip link set "$dev" down
>> +		ip link set "$dev" address "$newmac"
>> +		ip link set "$dev" up
>> +	fi
>> +
>> +	/etc/init.d/network restart
>> +}
>> +
>> +setupSwitch() {
>> +	# Set up switch for switch-based devices
>> +	# This is intended for initial setup, not for updates
>> +	# (changing ports will be sufficient then)
>> +	#
>> +	# Usage: setupSwitch <SWITCHDEV, e.g. eth0> <CLIENT_PORTS>
>> <BATMAN_PORTS> [<WAN_PORTS>]
>> +
>> +	local SWITCHDEV=$1
>> +	local CLIENT_PORTS=$2
>> +	local BATMAN_PORTS=$3
>> +	local WAN_PORTS=$4
>> +	local SWITCHHW
>> +
>> +	SWITCHHW="$(swconfig list | awk '{ print $4 }')"
>> +
>> +	uci set "network.switch=switch"
>> +	uci set "network.switch.name=$SWITCHHW"
>> +	uci set "network.switch.enable=1"
>> +	uci set "network.switch.reset=1"
>> +	uci set "network.switch.enable_vlan=1"
>> +
>> +	uci set "network.vlan1=switch_vlan"
>> +	uci set "network.vlan1.device=$SWITCHHW"
>> +	uci set "network.vlan1.vlan=1"
>> +	uci set "network.vlan1.ports=$CLIENT_PORTS"
>> +
>> +	# This defines the VLAN for WAN ports inside the switch.
>> +	# This is required even if the WAN eth is separate, but the WAN
>> port is in the switch!
>> +	if [ -n "$WAN_PORTS" ]; then
>> +		uci set "network.vlan2=switch_vlan"
>> +		uci set "network.vlan2.device=$SWITCHHW"
>> +		uci set "network.vlan2.vlan=2"
>> +		uci set "network.vlan2.ports=$WAN_PORTS"
>> +	fi
>> +
>> +	uci set "network.vlan3=switch_vlan"
>> +	uci set "network.vlan3.device=$SWITCHHW"
>> +	uci set "network.vlan3.vlan=3"
>> +	uci set "network.vlan3.ports=$BATMAN_PORTS"
>> +
>> +	uci set network.mesh.ifname="$SWITCHDEV.1 bat0"
>> +	uci set network.ethmesh.ifname="$SWITCHDEV.3"
>> +
>> +	uci commit network
>> +}
>> +
>> +setupWan() {
>> +	# Set up WAN for any device with dedicated port (no one-port where
>> mode is changed)
>> +	# This is intended for initial setup, not for updates
>> +	# (updates are only possible by changing ports in a switch)
>> +	#
>> +	# Usage: setupWan <WANDEV, e.g. eth0, eth0.2>
>> +
>> +	local WANDEV=$1
>> +
>> +	# This defines the WAN interface. We use the VLAN ID only if we do
>> NOT have a separate eth.
>> +	# This is different from the criterion for the WAN port dealt with
>> above!
>> +	# If the WANDEV is different from the SWITCHDEV, but the WAN port
>> is in the switch,
>> +	# the WAN eth has to be connected to the switch untagged!
>> +	enableAutoConf "$WANDEV"
>> +	uci set network.wan.ifname="$WANDEV"
>> +
>> +	uci commit network
>> +}
>> +
>> +setupOnePort() {
>> +	# Set up port mode for one-port devices
>> +	# This is intended for initial setup and for updates
>> +	# (latter will require network restart)
>> +	#
>> +	# Usage: setupOnePort <DEV, e.g. eth0> <ETHMODE, e.g. BATMAN,
>> CLIENT, WAN>
>> +
>> +	local DEV=$1
>> +	local ETHMODE=$2
>> +
>> +	uci set "network.$DEV=interface"
>> +	uci set "network.$DEV.ifname=$DEV"
>> +	if [ "$ETHMODE" = "WAN" ]; then
>> +		enableAutoConf "$DEV"
>> +		uci set network.mesh.ifname="bat0"
>> +		uci set network.wan.ifname="$DEV"
>> +		uci del network.ethmesh.ifname
>> +	elif [ "$ETHMODE" = "CLIENT" ] ; then
>> +		disableAutoConf "$DEV"
>> +		uci set network.mesh.ifname="bat0 $DEV"
>> +		uci del network.wan.ifname
>> +		uci del network.ethmesh.ifname
>> +	else # default=BATMAN
>> +		disableAutoConf "$DEV"
>> +		uci set network.mesh.ifname="bat0"
>> +		uci del network.wan.ifname
>> +		uci set network.ethmesh.ifname="$DEV"
>> +	fi
>> +	uci commit network
>> +}
>> diff --git
>> a/src/packages/fff/fff-network/files/lib/functions/fff/portorder
>> b/src/packages/fff/fff-network/files/lib/functions/fff/portorder
>> new file mode 100644
>> index 00000000..377c302f
>> --- /dev/null
>> +++ b/src/packages/fff/fff-network/files/lib/functions/fff/portorder
>> @@ -0,0 +1,31 @@
>> +# Copyright 2019 Adrian Schmutzler
>> +# License GPLv3
>> +
>> +BOARD="$(uci get board.model.name)"
>> +
>> +case "$BOARD" in
>> +	archer-c25-v1|\
>> +	archer-c60-v1|\
>> +	tl-wr841-v10|\
>> +	tl-wr841-v11|\
>> +	tl-wr841-v12)
>> +		PORTORDER="4 3 2 1"
>> +		;;
>> +	cpe210|\
>> +	cpe510)
>> +		PORTORDER="5 4"
>> +		;;
>> +	gl-ar150)
>> +		PORTORDER="1"
>> +		;;
>> +	tl-wdr4300-v1)
>> +		PORTORDER="1 2 3 4 5"
>> +		;;
>> +	tl-wr841-v8)
>> +		PORTORDER="2 3 4 1"
>> +		;;
>> +	tl-wr1043nd-v4|\
>> +	tl-wr1043n-v5)
>> +		PORTORDER="5 4 3 2 1"
>> +		;;
>> +esac
>> diff --git a/src/packages/fff/fff-network/files/usr/sbin/configurenetwork
>> b/src/packages/fff/fff-network/files/usr/sbin/configurenetwork
>> deleted file mode 100755
>> index 448bd04b..00000000
>> --- a/src/packages/fff/fff-network/files/usr/sbin/configurenetwork
>> +++ /dev/null
>> @@ -1,263 +0,0 @@
>> -#!/bin/sh
>> -# This program is free software; you can redistribute it and/or modify
>> -# it under the terms of the GNU General Public License as published by
>> -# the Free Software Foundation; either version 3 of the License, or
>> -# (at your option) any later version.
>> -
>> -# This program is distributed in the hope that it will be useful,
>> -# but WITHOUT ANY WARRANTY; without even the implied warranty of
>> -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> -# GNU General Public License for more details.
>> -
>> -. /lib/functions/fff/network
>> -
>> -setupPorts() {
>> -    # Add a single port to the *_PORTS config
>> -    # Usage: setupPorts <port id> <port mode>
>> -
>> -    local port=$1
>> -    local mode=$2
>> -
>> -    #default: BATMAN
>> -    if [ "$mode" = "WAN" ] ; then
>> -        WAN_PORTS="${WAN_PORTS} $port"
>> -    elif [ "$mode" = "CLIENT" ] ; then
>> -        CLIENT_PORTS="${CLIENT_PORTS} $port"
>> -    else
>> -        BATMAN_PORTS="${BATMAN_PORTS} $port"
>> -    fi
>> -}
>> -
>> -setAutoConf() {
>> -    # Sets ipv6 auto configuration on an interface to on/off
>> -    # Usage: setAutoConf <interface> <[0|1]>
>> -    local iface=$1
>> -    local on=$2
>> -
>> -    sysctlfile="/etc/sysctl.d/51-fff-network-$iface.conf"
>> -    echo "# Generated from configurenetwork" > "$sysctlfile"
>> -    echo "net.ipv6.conf.$iface.accept_ra = $on" >> "$sysctlfile"
>> -    echo "net.ipv6.conf.$iface.accept_ra_defrtr = $on" >> "$sysctlfile"
>> -    echo "net.ipv6.conf.$iface.accept_ra_pinfo = $on" >> "$sysctlfile"
>> -    echo "net.ipv6.conf.$iface.autoconf = $on" >> "$sysctlfile"
>> -    echo "net.ipv6.conf.$iface.accept_ra_rtr_pref = $on" >> "$sysctlfile"
>> -    echo "net.ipv6.conf.$iface.forwarding = 0" >> "$sysctlfile"
>> -
>> -    /sbin/sysctl -p "$sysctlfile"
>> -}
>> -
>> -enableAutoConf() {
>> -    # Enables ipv6 auto configuration on an interface
>> -    # Usage: enableAutoConf <interface>
>> -    local iface=$1
>> -
>> -    setAutoConf "$iface" "1"
>> -}
>> -
>> -disableAutoConf() {
>> -    # Disables ipv6 auto configuration on an interface
>> -    # Usage: disableAutoConf <interface>
>> -    local iface=$1
>> -
>> -    setAutoConf "$iface" "0"
>> -}
>> -
>> -BOARD="$(uci get board.model.name)"
>> -. /etc/network.$BOARD
>> -
>> -if [ -s /etc/network.config ] ; then
>> -    . /etc/network.config
>> -else
>> -    # Write network.config
>> -    echo "CLIENT_PORTS='$CLIENT_PORTS'" > /etc/network.config
>> -    echo "BATMAN_PORTS='$BATMAN_PORTS'" >> /etc/network.config
>> -    if [ -n "$WAN_PORTS" ] ; then
>> -        echo "WAN_PORTS='$WAN_PORTS'" >> /etc/network.config
>> -    fi
>> -    if [ "$ONE_PORT" = "YES" ] || [ -n "$ETHPORT" ] ; then
>> -        echo "ETHMODE='$ETHMODE' # use BATMAN, CLIENT or WAN" >>
>> /etc/network.config
>> -    fi
>> -    if [ -n "$LAN0PORT" ] ; then
>> -        echo "LAN0MODE='$LAN0MODE' # use BATMAN, CLIENT or WAN" >>
>> /etc/network.config
>> -    fi
>> -    if [ -n "$LAN1PORT" ] ; then
>> -        echo "LAN1MODE='$LAN1MODE' # use BATMAN, CLIENT or WAN" >>
>> /etc/network.config
>> -    fi
>> -    echo "FORCEPARSE='0' # Parse at: 0=first boot only, 1=every reboot,
>> 2=next reboot (once)" >> /etc/network.config
>> -fi
>> -
>> -if [ "$FORCEPARSE" = '2' ] ; then
>> -    sed -i '/^FORCEPARSE/d' /etc/network.config
>> -    echo "FORCEPARSE='0' # Parse at: 0=first boot only, 1=every reboot,
>> 2=next reboot (once)" >> /etc/network.config
>> -    FORCEPARSE='1'
>> -fi
>> -
>> -if [ -n "$ETHPORT" ] ; then
>> -    #LAN at AR150: default: BATMAN
>> -    setupPorts "$ETHPORT" "${ETHMODE}"
>> -fi
>> -if [ -n "$LAN0PORT" ] ; then
>> -    #LAN0 at two-port: default: BATMAN
>> -    setupPorts "$LAN0PORT" "${LAN0MODE}"
>> -fi
>> -if [ -n "$LAN1PORT" ] ; then
>> -    #LAN1 at two-port: default: BATMAN
>> -    setupPorts "$LAN1PORT" "${LAN1MODE}"
>> -fi
>> -
>> -if ! uci -q get network.$SWITCHDEV > /dev/null || [ "$FORCEPARSE" = '1' ]
>> ; then
>> -
>> -    SWITCHHW=$(swconfig list | awk '{ print $4 }')
>> -
>> -    uci set network.$SWITCHDEV=switch
>> -    uci set network.$SWITCHDEV.name=$SWITCHHW
>> -    uci set network.$SWITCHDEV.enable=1
>> -    uci set network.$SWITCHDEV.reset=1
>> -    uci set network.$SWITCHDEV.enable_vlan=1
>> -
>> -    uci set network.${SWITCHDEV}_1=switch_vlan
>> -    uci set network.${SWITCHDEV}_1.device=$SWITCHHW
>> -    uci set network.${SWITCHDEV}_1.vlan=1
>> -    uci set network.${SWITCHDEV}_1.ports="$CLIENT_PORTS"
>> -
>> -    if [ "$WANDEV" = "$SWITCHDEV" ] || ! [ -z "$WAN_PORTS" ]; then
>> -        uci set network.${SWITCHDEV}_2=switch_vlan
>> -        uci set network.${SWITCHDEV}_2.device=$SWITCHHW
>> -        uci set network.${SWITCHDEV}_2.vlan=2
>> -        uci set network.${SWITCHDEV}_2.ports="$WAN_PORTS"
>> -
>> -        enableAutoConf "$WANDEV.2"
>> -    else
>> -        enableAutoConf "$WANDEV"
>> -    fi
>> -
>> -    uci set network.${SWITCHDEV}_3=switch_vlan
>> -    uci set network.${SWITCHDEV}_3.device=$SWITCHHW
>> -    uci set network.${SWITCHDEV}_3.vlan=3
>> -    uci set network.${SWITCHDEV}_3.ports="$BATMAN_PORTS"
>> -
>> -    uci set network.mesh.ifname="$SWITCHDEV.1 bat0"
>> -
>> -    uci set network.ethmesh.ifname="$SWITCHDEV.3"
>> -
>> -    if [ "$WANDEV" = "$SWITCHDEV" ]; then
>> -        uci set network.wan.ifname=$WANDEV.2
>> -    else
>> -        uci set network.wan.ifname=$WANDEV
>> -    fi
>> -
>> -    uci commit network
>> -fi
>> -
>> -if [ "$ONE_PORT" = "YES" ] && ( ! uci -q get network.$SWITCHDEV.ifname ||
>> [ "$FORCEPARSE" = '1' ] ) ; then
>> -    uci set network.$SWITCHDEV=interface
>> -    uci set network.$SWITCHDEV.ifname=$SWITCHDEV
>> -    if [ "$ETHMODE" = "WAN" ]; then
>> -        enableAutoConf "$WANDEV"
>> -        uci set network.mesh.ifname="bat0"
>> -        uci set network.wan.ifname="$WANDEV"
>> -        uci del uci set network.ethmesh.ifname
>> -        uci del network.eth0.macaddr
>> -    elif [ "$ETHMODE" = "CLIENT" ] ; then
>> -        disableAutoConf "$WANDEV"
>> -        uci set network.mesh.ifname="bat0 $SWITCHDEV"
>> -        uci set network.wan.ifname="eth1" #eth1 because it is default in
>> config file
>> -        uci del network.ethmesh.ifname
>> -        uci del network.eth0.macaddr
>> -    elif [ "$ETHMODE" = "BATMAN" ] ; then
>> -        disableAutoConf "$WANDEV"
>> -        uci set network.mesh.ifname="bat0"
>> -        uci set network.wan.ifname="eth1" #eth1 because it is default in
>> config file
>> -        uci set network.ethmesh.ifname="$SWITCHDEV"
>> -        ETH0MAC="w2ap"
>> -    fi
>> -    uci commit network
>> -fi
>> -
>> -/etc/init.d/network restart
>> -
>> -if [ -n "$ETHMESHMAC" ]; then
>> -    if uci get network.ethmesh.macaddr
>> -    then
>> -        echo "MAC for ethmesh is set already"
>> -    else
>> -        echo "Fixing MAC on $SWITCHDEV.3 (ethmesh)"
>> -        sleep 10
>> -
>> -        uci set network.ethmesh.macaddr=$ETHMESHMAC
>> -        uci commit network
>> -
>> -        ifconfig $SWITCHDEV.3 down
>> -        ifconfig $SWITCHDEV.3 hw ether $ETHMESHMAC
>> -        ifconfig $SWITCHDEV.3 up
>> -        /etc/init.d/network restart
>> -    fi
>> -fi
>> -
>> -if [ -n "$ROUTERMAC" ]; then
>> -    if uci get network.mesh.macaddr
>> -    then
>> -        echo "MAC for mesh is set already"
>> -    else
>> -        echo "Fixing MAC on br-mesh (mesh)"
>> -        sleep 10
>> -
>> -        uci set network.mesh.macaddr=$ROUTERMAC
>> -        uci commit network
>> -
>> -        ifconfig br-mesh down
>> -        ifconfig br-mesh hw ether $ROUTERMAC
>> -        ifconfig br-mesh up
>> -        /etc/init.d/network restart
>> -    fi
>> -fi
>> -
>> -if [ -n "$ETH0MAC" ]; then
>> -        echo "Fixing MAC on eth0"
>> -        sleep 10
>> -        NEW_MACADDR=$(cat "/sys/class/net/${ETH0MAC}/address")
>> -        uci set network.eth0.macaddr=$NEW_MACADDR
>> -        uci commit network
>> -        ifconfig eth0 down
>> -        ifconfig eth0 hw ether $NEW_MACADDR
>> -        ifconfig eth0 up
>> -        /etc/init.d/network restart
>> -fi
>> -
>> -if uci -q get "network.mesh.ip6addr" > /dev/null
>> -then
>> -    echo "IPv6 for mesh is set already"
>> -else
>> -    echo "Setting IPv6 addresses"
>> -    # Some time needed :(
>> -    sleep 5
>> -
>> -    for ip in $(ip -6 addr show br-mesh | awk '/fdff/{ print $2 }'); do
>> -        ip -6 addr del $ip dev br-mesh
>> -    done
>> -
>> -    prefix="fdff:0::/64"
>> -    # Set $prefix::MAC as IP
>> -    addr="$(ipMacAssemble "$prefix" "$ROUTERMAC")"
>> -    ip -6 addr add $addr dev br-mesh
>> -
>> -    uci -q del network.globals
>> -    uci -q set network.globals=globals
>> -    uci -q set network.globals.ula_prefix=$prefix
>> -    uci -q add_list network.mesh.ip6addr=$addr
>> -    uci -q set network.mesh.proto=static
>> -
>> -    # Set $prefix::1 as IP
>> -    addr="$(ipAssemble "$prefix" "1")"
>> -    ip -6 addr add $addr dev br-mesh
>> -    uci -q add_list network.mesh.ip6addr=$addr
>> -
>> -    # Set $prefix::link-local as IP
>> -    addr="$(ipEUIAssemble "$prefix" "$ROUTERMAC")"
>> -    ip -6 addr add $addr dev br-mesh
>> -    uci -q add_list network.mesh.ip6addr=$addr
>> -
>> -    uci -q commit network
>> -
>> -    /etc/init.d/fff-uradvd restart
>> -fi
>> diff --git a/src/packages/fff/fff-sysupgrade/Makefile
>> b/src/packages/fff/fff-sysupgrade/Makefile
>> index 90ef66af..0e6c08ec 100644
>> --- a/src/packages/fff/fff-sysupgrade/Makefile
>> +++ b/src/packages/fff/fff-sysupgrade/Makefile
>> @@ -1,8 +1,7 @@
>>  include $(TOPDIR)/rules.mk
>>
>>  PKG_NAME:=fff-sysupgrade
>> -PKG_VERSION:=9
>> -PKG_RELEASE:=1
>> +PKG_RELEASE:=10
>>
>>  PKG_BUILD_DIR:=$(BUILD_DIR)/$(PKG_NAME)
>>
>> diff --git
>> a/src/packages/fff/fff-sysupgrade/files/etc/uci-defaults/99-fff-sysupgrade
>> b/src/packages/fff/fff-sysupgrade/files/etc/uci-defaults/99-fff-sysupgrade
>> index 7ff83f54..f5783687 100644
>> ---
>> a/src/packages/fff/fff-sysupgrade/files/etc/uci-defaults/99-fff-sysupgrade
>> +++
>> b/src/packages/fff/fff-sysupgrade/files/etc/uci-defaults/99-fff-sysupgrade
>> @@ -7,7 +7,6 @@ cat > /etc/sysupgrade.conf <<-__EOF__
>>  /etc/dropbear/dropbear_dss_host_key
>>  /etc/dropbear/dropbear_rsa_host_key
>>  /etc/dropbear/authorized_keys
>> -/etc/network.config
>>  /etc/config/fff
>>  /etc/hoodfile
>>  __EOF__
>> --
>> 2.11.0

-------------- nächster Teil --------------
Ein Dateianhang mit Binärdaten wurde abgetrennt...
Dateiname   : signature.asc
Dateityp    : application/pgp-signature
Dateigröße  : 833 bytes
Beschreibung: OpenPGP digital signature
URL         : <https://{'listname': 'franken-dev-freifunk.net', 'hostname': 'lists.freifunk.net'}/pipermail/franken-dev-freifunk.net/attachments/20190424/850563e7/attachment.sig>


Mehr Informationen über die Mailingliste franken-dev