Re: Kernel 4.4.92 und höher macht Unifi AC Mesh kaputt
Christian Dresel
fff at chrisi01.de
Mi Jan 3 00:08:14 CET 2018
Hi
Am 3. Januar 2018 00:01:05 MEZ schrieb mail at adrianschmutzler.de:
>Hallo zusammen,
>
>habe das gerade mal durchgetestet:
>
>Das LEDE Kernel-Update auf 4.4.92 macht die Unifi AC Mesh kaputt,
>sodass
>bat0 nicht mehr geht. Wenn ich Christian richtig verstanden habe, fehlt
>das
>Kernel-Modul ganz?!
Es scheinen ALLE Kernel Module zu fehlen, logread meckert auch über iptables und ebtables und lsmod ist komplett leer. Ein Wunder daß man das Ding dann überhaupt noch erreicht.
>
>Habe den Commit direkt davor getestet:
>https://github.com/lede-project/source/commit/e6fd17d04c7d738598414c55cd091f
>7fb9c6567a
>=> Läuft normal
>
>Mit Kernel-Update:
>https://github.com/lede-project/source/commit/fa0b5fce1f53c3520cacff49e9d371
>fb2c5c3685
>=> Läuft nicht
>
>Ursprünglich hatte ich die aktuelle Version (Stand 2018-01-01, Kernel
>4.4.108) verwendet:
>https://github.com/lede-project/source/commit/473e99457156209bf37ab15b4b7f3e
>d94b15dc0c
>=> Läuft auch nicht, also wurde hier nichts zwischendurch gefixt
>
>Betroffen ist nur das reine LEDE Patchlevel, nicht packages oder
>routing.
>
>Auf einem WR841N v12 läuft die neue Version (2018-01-01) problemlos,
>ist
>also spezifisch für die AC-Mesh?!
Wdr4300 geht bei mir auch problemlos und einen 4900er habe ich glaub ich auch schon damit laufen. Denkbar daß es nur den ac Mesh betrifft. Was da passiert kann ich aber aktuell auch nicht beurteilen. Andere ubiquiti Geräte wären mal interessant.
Mfg
Christian
>
>Mit etwas Glück gibt es jetzt nach dem OpenWRT Remerge auch mal wieder
>eine
>neue Hauptversion, die dann Kernel 4.9 oder 4.14 hat. Vielleicht hilft
>das... (oder alles wird schlimmer ;-))
>
>Grüße
>
>Adrian
>
>
>> -----Original Message-----
>> From: franken-dev [mailto:franken-dev-bounces at freifunk.net] On Behalf
>> Of mail at adrianschmutzler.de
>> Sent: Dienstag, 2. Januar 2018 20:55
>> To: 'Christian Dresel' <fff at chrisi01.de>; franken-dev at freifunk.net
>> Subject: RE: [PATCH] configurenetwork: Rearrangement/redesign of
>central
>> commands
>>
>> Kann eigtl nur das Kernel-Update sein:
>>
>> https://github.com/openwrt/openwrt/commit/fa0b5fce1f53c3520cacff49e9
>> d371fb2c5c3685
>>
>> Werde mal mit und ohne Testen.
>>
>> > -----Original Message-----
>> > From: Christian Dresel [mailto:fff at chrisi01.de]
>> > Sent: Dienstag, 2. Januar 2018 20:52
>> > To: mail at adrianschmutzler.de; franken-dev at freifunk.net
>> > Subject: Re: [PATCH] configurenetwork: Rearrangement/redesign of
>> > central commands
>> >
>> >
>> >
>> > On 02.01.2018 20:49, mail at adrianschmutzler.de wrote:
>> > > Ich hab routing gar nicht geupdatet, aber packages. Hast du
>packages
>> > mitgezogen oder nicht?
>> >
>> > packages hab ich nicht mitgezogen, nur LEDE und Routing.
>> >
>> > demnach würde ich sagen, das Problem entsteht im LEDE irgendwo.
>> >
>> > >
>> > >> -----Original Message-----
>> > >> From: Christian Dresel [mailto:fff at chrisi01.de]
>> > >> Sent: Dienstag, 2. Januar 2018 20:48
>> > >> To: mail at adrianschmutzler.de
>> > >> Subject: Re: [PATCH] configurenetwork: Rearrangement/redesign of
>> > >> central commands
>> > >>
>> > >> hi
>> > >>
>> > >> On 02.01.2018 20:46, mail at adrianschmutzler.de wrote:
>> > >>> Argh...
>> > >>>
>> > >>> Danke, da kann ich natürlich stundenlang an meiner Config
>> > >>> rumschrauben,
>> > >> wenn einfach das Modul fehlt. Wie mein Physik-Prof. halt immer
>> > >> gesagt
>> > hat:
>> > >> Immer nur einen Parameter gleichzeitig ändern ....
>> > >>>
>> > >>> Du hast wirklich genau 17.01.4 genommen? Weil dann kann ich
>> > >> einschränken, wo ich bei LEDE suchen muss...
>> > >>
>> > >> bei der LEDE Git Nummer bin ich mir sicher (ich erinner mich an
>die
>> > >> drei 4er am Anfang) beim Routingfeed weiß ich es nicht exakt, es
>> > >> war auf jeden Fall einer wo Batman 2017.3 drinnen ist aber noch
>> > >> nicht Batman
>> > >> 2017.4 (das hat nicht gebaut und beim build abgebrochen weil
>> > >> irgendein C- Code kaputt war).
>> > >>
>> > >> P.S. die ML vergessen? Wann ja bitte wieder dort hin antworten,
>> > >> interessiert bestimmt auch andere ;)
>> > >>
>> > >> mfg
>> > >>
>> > >> Christian
>> > >>
>> > >>>
>> > >>> Grüße
>> > >>>
>> > >>> Adrian
>> > >>>
>> > >>>> -----Original Message-----
>> > >>>> From: Christian Dresel [mailto:fff at chrisi01.de]
>> > >>>> Sent: Dienstag, 2. Januar 2018 20:18
>> > >>>> To: mail at adrianschmutzler.de; franken-dev at freifunk.net
>> > >>>> Subject: Re: [PATCH] configurenetwork: Rearrangement/redesign
>of
>> > >>>> central commands
>> > >>>>
>> > >>>> hi
>> > >>>>
>> > >>>> On 02.01.2018 20:05, mail at adrianschmutzler.de wrote:
>> > >>>>> Tested successfully on WR841N v12.
>> > >>>>> On ONEPORT (AC Mesh), bat0 is not coming up and thus br-mesh
>is
>> > >>>> missing...
>> > >>>>>
>> > >>>>> Open issues:
>> > >>>>> ...
>> > >>>>> - Why is bat0 not coming up on AC Mesh? Help please...
>> > >>>>
>> > >>>> das ist mir gestern auch passiert. Ich hab nur unseren
>aktuellen
>> > >>>> Master hergenommen und LEDE auf 17.01.4
>> > >>>> (444add156f2a6d92fc15005c5ade2208a978966c) hochgezogen, sowie
>> > den
>> > >>>> Routingfeed auf 78049b46ac7cfbb14e8f05bc5150f518f827c0ec.
>> > >>>>
>> > >>>> Auch hier war nur eth0 und lo offen aber kein bat0, kein
>br-mesh
>o.ä.
>> > >>>> Ich hab nach langen suchen den Fehler nicht gefunden, wieder
>den
>> > >>>> aktuellen Master gebaut und dann lief es wieder. Warum das
>> > >>>> passiert,
>> > >> keine Ahnung.
>> > >>>> Es scheinen auch alle Kernelmodule zu fehlen (lsmod) ein
>wunder
>> > >>>> das er überhaupt geht ;)
>> > >>>>
>> > >>>> Bei mir ebenfalls der AC Mesh.
>> > >>>>
>> > >>>> mfg
>> > >>>>
>> > >>>> Christian
>> > >>>>
>> > >>>>>
>> > >>>>> Grüße
>> > >>>>>
>> > >>>>> Adrian
>> > >>>>>
>> > >>>>>> -----Original Message-----
>> > >>>>>> From: franken-dev [mailto:franken-dev-bounces at freifunk.net]
>> On
>> > >>>> Behalf
>> > >>>>>> Of Adrian Schmutzler
>> > >>>>>> Sent: Dienstag, 2. Januar 2018 20:02
>> > >>>>>> To: franken-dev at freifunk.net
>> > >>>>>> Subject: [PATCH] configurenetwork: Rearrangement/redesign of
>> > >>>>>> central commands
>> > >>>>>>
>> > >>>>>> This patch rearranges the commands in configurenetwork. The
>> > >>>>>> main goal is
>> > >>>>> to
>> > >>>>>> avoid code duplications and make reading easier. Some "bugs"
>> > >>>>>> were addressed on the way:
>> > >>>>>> - Previously, ONEPORT devices went through both major
>blocks,
>> > >>>>>> resulting e.g. in useless eth0.X interfaces being set up
>(and
>> > >>>>>> perhaps lots of other strange things). Now, the routines
>for
>> > >>>>>> ONEPORT and normal devices are separated.
>> > >>>>>> - Updating the /etc/sysctl.conf has been combined to a
>single
>> > >>>>>> block based on variables set earlier
>> > >>>>>> - WANDEV is reset to WANDEV.2 were applicable to reduce
>> number
>> > of
>> > >>>>>> ifs
>> > >>>>>> - "uci del uci set" has been changed to "uci del"
>> > >>>>>> - Spaces have been changed to Tabs were changes were done
>> > >>>>>> - Arguments have been quoted in various places
>> > >>>>>> - Double brackets have been replaced by single brackets
>> > >>>>>> - ETHMODE if has been changed to use BATMAN as default
>(elseif
>> > >>>>>> changed to else)
>> > >>>>>> - Use ETHMESHMAC for ONEPORT, introduce ETHMESHDEV
>> > >>>>>>
>> > >>>>>> Signed-off-by: Adrian Schmutzler
><freifunk at adrianschmutzler.de>
>> > >>>>>>
>> > >>>>>> ---
>> > >>>>>>
>> > >>>>>> This requires the patches to be applied BEFOREHAND:
>> > >>>>>> fff-network: Introduce function to set MAC on device
>> > >>>>>> fff-network: Replace ETH0MAC by replacement based on
>> > ROUTERMAC
>> > >>>>>>
>> > >>>>>> Open issues:
>> > >>>>>> - Line 84/89: eth0 MAC address is deleted (!). Why is this
>done
>> > >>>>>> only in uci and is it desirable to have a device without
>MAC?
>> > >>>>>> ---
>> > >>>>>> .../fff-network/files/usr/sbin/configurenetwork | 155
>> > >>>>> ++++++++++---------
>> > >>>>>> --
>> > >>>>>> 1 file changed, 70 insertions(+), 85 deletions(-)
>> > >>>>>>
>> > >>>>>> diff --git
>> > >>>>>>
>a/src/packages/fff/fff-network/files/usr/sbin/configurenetwork
>> > >>>>>>
>b/src/packages/fff/fff-network/files/usr/sbin/configurenetwork
>> > >>>>>> index 0fbff10..ded9485 100755
>> > >>>>>> ---
>> > >>>>>>
>a/src/packages/fff/fff-network/files/usr/sbin/configurenetwork
>> > >>>>>> +++
>b/src/packages/fff/fff-network/files/usr/sbin/configurenetw
>> > >>>>>> +++ or
>> > >>>>>> +++ k
>> > >>>>>> @@ -71,96 +71,81 @@ if [ -n "$LAN1PORT" ] ; then
>> > >>>>>> setupPorts "$LAN1PORT" "${LAN1MODE}"
>> > >>>>>> fi
>> > >>>>>>
>> > >>>>>> -if ! uci -q get network.$SWITCHDEV > /dev/null || [
>> "$FORCEPARSE"
>> > >>>>>> = '1' ]
>> > >>>>> ;
>> > >>>>>> then
>> > >>>>>> -
>> > >>>>>> - SWITCHHW=$(swconfig list | awk '{ print $4 }')
>> > >>>>>> -
>> > >>>>>> - uci set network.$SWITCHDEV=switch
>> > >>>>>> - uci set network.$SWITCHDEV.name=$SWITCHHW
>> > >>>>>> - uci set network.$SWITCHDEV.enable=1
>> > >>>>>> - uci set network.$SWITCHDEV.reset=1
>> > >>>>>> - uci set network.$SWITCHDEV.enable_vlan=1
>> > >>>>>> -
>> > >>>>>> - uci set network.${SWITCHDEV}_1=switch_vlan
>> > >>>>>> - uci set network.${SWITCHDEV}_1.device=$SWITCHHW
>> > >>>>>> - uci set network.${SWITCHDEV}_1.vlan=1
>> > >>>>>> - uci set network.${SWITCHDEV}_1.ports="$CLIENT_PORTS"
>> > >>>>>> -
>> > >>>>>> - echo "# Allow IPv6 RAs on WAN Port" >> /etc/sysctl.conf
>> > >>>>>> -
>> > >>>>>> - if [[ "$WANDEV" = "$SWITCHDEV" ]] || ! [[ -z
>"$WAN_PORTS"
>]];
>> > >> then
>> > >>>>>> - uci set network.${SWITCHDEV}_2=switch_vlan
>> > >>>>>> - uci set network.${SWITCHDEV}_2.device=$SWITCHHW
>> > >>>>>> - uci set network.${SWITCHDEV}_2.vlan=2
>> > >>>>>> - uci set network.${SWITCHDEV}_2.ports="$WAN_PORTS"
>> > >>>>>> -
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.2.accept_ra_defrtr = 1"
>>>
>> > >>>>>> /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.2.accept_ra_pinfo = 1"
>>>
>> > >>>>>> /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.2.autoconf = 1" >>
>> > /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.2.accept_ra_rtr_pref =
>1" >>
>> > >>>>>> /etc/sysctl.conf
>> > >>>>>> - else
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_defrtr = 1"
>>>
>> > >>>>> /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_pinfo = 1" >>
>> > >>>>> /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.autoconf = 1" >>
>> > /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_rtr_pref = 1"
>>>
>> > >>>>>> /etc/sysctl.conf
>> > >>>>>> - fi
>> > >>>>>> -
>> > >>>>>> - uci set network.${SWITCHDEV}_3=switch_vlan
>> > >>>>>> - uci set network.${SWITCHDEV}_3.device=$SWITCHHW
>> > >>>>>> - uci set network.${SWITCHDEV}_3.vlan=3
>> > >>>>>> - uci set network.${SWITCHDEV}_3.ports="$BATMAN_PORTS"
>> > >>>>>> -
>> > >>>>>> - uci set network.mesh.ifname="$SWITCHDEV.1 bat0"
>> > >>>>>> -
>> > >>>>>> - uci set network.ethmesh.ifname="$SWITCHDEV.3"
>> > >>>>>> -
>> > >>>>>> - if [[ "$WANDEV" = "$SWITCHDEV" ]]; then
>> > >>>>>> - uci set network.wan.ifname=$WANDEV.2
>> > >>>>>> - else
>> > >>>>>> - uci set network.wan.ifname=$WANDEV
>> > >>>>>> - fi
>> > >>>>>> -
>> > >>>>>> - uci commit network
>> > >>>>>> +if [ "$ONE_PORT" = "YES" ] ; then
>> > >>>>>> + if ! uci -q get "network.$SWITCHDEV.ifname" || [
>> > "$FORCEPARSE"
>> > >>>>>> +=
>> > >>>>>> '1' ] ; then
>> > >>>>>> + uci set "network.$SWITCHDEV=interface"
>> > >>>>>> + uci set "network.$SWITCHDEV.ifname=$SWITCHDEV"
>> > >>>>>> + wanon="0"
>> > >>>>>> + if [ "$ETHMODE" = "WAN" ]; then
>> > >>>>>> + wanon="1"
>> > >>>>>> + uci set network.mesh.ifname="bat0"
>> > >>>>>> + uci set network.wan.ifname="$WANDEV"
>> > >>>>>> + uci del network.ethmesh.ifname
>> > >>>>>> + uci del network.eth0.macaddr
>> > >>>>>> + elif [ "$ETHMODE" = "CLIENT" ] ; then
>> > >>>>>> + uci set network.mesh.ifname="bat0
>> > $SWITCHDEV"
>> > >>>>>> + uci set network.wan.ifname="eth1" #eth1
>> > because it
>> > >>>>>> is default in config file
>> > >>>>>> + uci del network.ethmesh.ifname
>> > >>>>>> + uci del network.eth0.macaddr
>> > >>>>>> + else # default=BATMAN
>> > >>>>>> + uci set network.mesh.ifname="bat0"
>> > >>>>>> + uci set network.wan.ifname="eth1" #eth1
>> > because it
>> > >>>>>> is default in config file
>> > >>>>>> + uci set
>> > network.ethmesh.ifname="$SWITCHDEV"
>> > >>>>>> + ETHMESHMAC="$(macFlipLocalBit
>> > "$ROUTERMAC")"
>> > >>>>>> + ETHMESHDEV="$SWITCHDEV"
>> > >>>>>> + fi
>> > >>>>>> + uci -q commit network
>> > >>>>>> + fi
>> > >>>>>> +else
>> > >>>>>> + if ! uci -q get "network.$SWITCHDEV" > /dev/null || [
>> > "$FORCEPARSE"
>> > >>>>>> = '1' ] ; then
>> > >>>>>> + SWITCHHW="$(swconfig list | awk '{ print $4 }')"
>> > >>>>>> +
>> > >>>>>> + uci set "network.$SWITCHDEV=switch"
>> > >>>>>> + uci set "network.$SWITCHDEV.name=$SWITCHHW"
>> > >>>>>> + uci set "network.$SWITCHDEV.enable=1"
>> > >>>>>> + uci set "network.$SWITCHDEV.reset=1"
>> > >>>>>> + uci set "network.$SWITCHDEV.enable_vlan=1"
>> > >>>>>> +
>> > >>>>>> + uci set "network.${SWITCHDEV}_1=switch_vlan"
>> > >>>>>> + uci set
>> > "network.${SWITCHDEV}_1.device=$SWITCHHW"
>> > >>>>>> + uci set "network.${SWITCHDEV}_1.vlan=1"
>> > >>>>>> + uci set
>> > "network.${SWITCHDEV}_1.ports=$CLIENT_PORTS"
>> > >>>>>> +
>> > >>>>>> + echo "# Allow IPv6 RAs on WAN Port" >>
>> > /etc/sysctl.conf
>> > >>>>>> +
>> > >>>>>> + wanon="1"
>> > >>>>>> + if [ "$WANDEV" = "$SWITCHDEV" ] || [ -n
>> > "$WAN_PORTS" ];
>> > >>>>>> then
>> > >>>>>> + WANDEV="${SWITCHDEV}.2"
>> > >>>>>> + uci set
>> > "network.${SWITCHDEV}_2=switch_vlan"
>> > >>>>>> + uci set
>> > >>>>>> "network.${SWITCHDEV}_2.device=$SWITCHHW"
>> > >>>>>> + uci set "network.${SWITCHDEV}_2.vlan=2"
>> > >>>>>> + uci set
>> > >>>>>> "network.${SWITCHDEV}_2.ports=$WAN_PORTS"
>> > >>>>>> + fi
>> > >>>>>> +
>> > >>>>>> + ETHMESHDEV="$SWITCHDEV.3"
>> > >>>>>> + uci set "network.${SWITCHDEV}_3=switch_vlan"
>> > >>>>>> + uci set
>> > "network.${SWITCHDEV}_3.device=$SWITCHHW"
>> > >>>>>> + uci set "network.${SWITCHDEV}_3.vlan=3"
>> > >>>>>> + uci set
>> > "network.${SWITCHDEV}_3.ports=$BATMAN_PORTS"
>> > >>>>>> +
>> > >>>>>> + uci set network.mesh.ifname="$SWITCHDEV.1 bat0"
>> > >>>>>> + uci set network.wan.ifname="$WANDEV"
>> > >>>>>> + uci set network.ethmesh.ifname="$ETHMESHDEV"
>> > >>>>>> +
>> > >>>>>> + uci -q commit network
>> > >>>>>> + fi
>> > >>>>>> fi
>> > >>>>>> -
>> > >>>>>> -if [ "$ONE_PORT" = "YES" ] && ( ! uci -q get
>> > >>>>>> network.$SWITCHDEV.ifname || [ "$FORCEPARSE" = '1' ] ) ;
>then
>> > >>>>>> - uci set network.$SWITCHDEV=interface
>> > >>>>>> - uci set network.$SWITCHDEV.ifname=$SWITCHDEV
>> > >>>>>> - if [ "$ETHMODE" = "WAN" ]; then
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_defrtr = 1"
>>>
>> > >>>>> /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_pinfo = 1" >>
>> > >>>>> /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.autoconf = 1" >>
>> > /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_rtr_pref = 1"
>>>
>> > >>>>>> /etc/sysctl.conf
>> > >>>>>> - uci set network.mesh.ifname="bat0"
>> > >>>>>> - uci set network.wan.ifname="$WANDEV"
>> > >>>>>> - uci del uci set network.ethmesh.ifname
>> > >>>>>> - uci del network.eth0.macaddr
>> > >>>>>> - elif [ "$ETHMODE" = "CLIENT" ] ; then
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_defrtr = 0"
>>>
>> > >>>>> /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_pinfo = 0" >>
>> > >>>>> /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.autoconf = 0" >>
>> > /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_rtr_pref = 0"
>>>
>> > >>>>>> /etc/sysctl.conf
>> > >>>>>> - uci set network.mesh.ifname="bat0 $SWITCHDEV"
>> > >>>>>> - uci set network.wan.ifname="eth1" #eth1 because it
>is
>> default
>> > in
>> > >>>>> config
>> > >>>>>> file
>> > >>>>>> - uci del network.ethmesh.ifname
>> > >>>>>> - uci del network.eth0.macaddr
>> > >>>>>> - elif [ "$ETHMODE" = "BATMAN" ] ; then
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_defrtr = 0"
>>>
>> > >>>>> /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_pinfo = 0" >>
>> > >>>>> /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.autoconf = 0" >>
>> > /etc/sysctl.conf
>> > >>>>>> - echo "net.ipv6.conf.$WANDEV.accept_ra_rtr_pref = 0"
>>>
>> > >>>>>> /etc/sysctl.conf
>> > >>>>>> - uci set network.mesh.ifname="bat0"
>> > >>>>>> - uci set network.wan.ifname="eth1" #eth1 because it
>is
>> default
>> > in
>> > >>>>> config
>> > >>>>>> file
>> > >>>>>> - uci set network.ethmesh.ifname="$SWITCHDEV"
>> > >>>>>> - fixMac "$(macFlipLocalBit "$ROUTERMAC")" "eth0"
>"eth0"
>"1"
>> > >>>>>> - fi
>> > >>>>>> - uci commit network
>> > >>>>>> +if [ -n "$wanon" ]; then
>> > >>>>>> + echo "net.ipv6.conf.$WANDEV.accept_ra_defrtr = $wanon"
>> > >>
>> > >>>>>> /etc/sysctl.conf
>> > >>>>>> + echo "net.ipv6.conf.$WANDEV.accept_ra_pinfo = $wanon"
>> > >>
>> > >>>>>> /etc/sysctl.conf
>> > >>>>>> + echo "net.ipv6.conf.$WANDEV.autoconf = $wanon" >>
>> > >>>>>> /etc/sysctl.conf
>> > >>>>>> + echo "net.ipv6.conf.$WANDEV.accept_ra_rtr_pref =
>> > $wanon" >>
>> > >>>>>> +/etc/sysctl.conf
>> > >>>>>> fi
>> > >>>>>>
>> > >>>>>> /etc/init.d/network restart
>> > >>>>>>
>> > >>>>>> -if [ -n "$ETHMESHMAC" ]; then
>> > >>>>>> - fixMac "$ETHMESHMAC" "${SWITCHDEV}.3" "ethmesh"
>> > >>>>>> +if [ -n "$ETHMESHMAC" ] && [ -n "$ETHMESHDEV" ]; then
>> > >>>>>> + fixMac "$ETHMESHMAC" "$ETHMESHDEV" "ethmesh"
>> > >>>>>> fi
>> > >>>>>>
>> > >>>>>> if [ -n "$ROUTERMAC" ]; then
>> > >>>>>> --
>> > >>>>>> 2.7.4
>> > >>>>>>
>> > >>>>>> --
>> > >>>>>> franken-dev mailing list
>> > >>>>>> franken-dev at freifunk.net
>> > >>>>>>
>http://lists.freifunk.net/mailman/listinfo/franken-dev-freifunk
>> > >>>>>> .n
>> > >>>>>> et
>> > >>>>>
>> > >>>
>> > >>>
>> > >
>> > >
>>
>>
>> --
>> franken-dev mailing list
>> franken-dev at freifunk.net
>> http://lists.freifunk.net/mailman/listinfo/franken-dev-freifunk.net
--
Diese Nachricht wurde von meinem Android-Gerät mit K-9 Mail gesendet.
Mehr Informationen über die Mailingliste franken-dev