[PATCH v16 4/6] Add fff-hoods
mail at adrianschmutzler.de
mail at adrianschmutzler.de
Sa Okt 14 01:04:26 CEST 2017
Hallo Christian,
mein Patch für den C25 steht in der network.*, d.h. 5 GHz wird VOR dem configurehood deaktiviert. Da letzteres alles neu konfiguriert, geht diese Einstellung dann verloren. Mir fällt aber grade nichts ein, wie ich nur für den C25 NACH der configurehood 5 GHz wieder ausschalten kann.
Im schlimmsten Fall müsste man den C25 wieder rauspatchen...
Grüße
Adrian
> -----Original Message-----
> From: franken-dev [mailto:franken-dev-bounces at freifunk.net] On Behalf
> Of Christian Dresel
> Sent: Dienstag, 10. Oktober 2017 16:39
> To: Adrian Schmutzler <freifunk at adrianschmutzler.de>; franken-
> dev at freifunk.net
> Cc: Jan Kraus <mayosemmel at gmail.com>
> Subject: Re: [PATCH v16 4/6] Add fff-hoods
>
> Nach einen reboot lief er dann richtig, wifi geht wieder und auch das configap
> hat die fe80::1 bekommen. Dazu ist nun auch das radio für 5GHz aus, das war
> interessanterweise beim c25 an (??)
>
> mfg
>
> Christian
>
> On 10.10.2017 15:05, Christian Dresel wrote:
> > Im jetztigen Zustand ist vermutlich auch folgendes sehr interessant:
> >
> > root at c25testknoten:/tmp# wifi
> > Command failed: Request timed out
> > root at c25testknoten:/tmp#
> >
> >
> > mfg
> >
> > Christian
> >
> > On 10.10.2017 15:02, Christian Dresel wrote:
> >> hi
> >>
> >> On 06.10.2017 15:45, Christian Dresel wrote:
> >>> hi
> >>>
> >>> On 05.10.2017 15:37, Adrian Schmutzler wrote:
> >>>> From: Christian Dresel <fff at chrisi01.de>
> >>>>
> >>>> This package connects to keyxchangev2
> >>>>
> >>>> Signed-off-by: Christian Dresel <fff at chrisi01.de>
> >>>> Signed-off-by: Jan Kraus <mayosemmel at gmail.com>
> >>>> Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>
> >>>>
> >>>> Update in v2:
> >>>> - clean tabstops
> >>>> - move the json vpn out of the if because we need this after
> >>>> reboot
> >>>>
> >>>> Update in v5:
> >>>> !!UNTESTED!!
> >>>> - change hidden AP ip to locallink
> >>>> - Open hidden AP after more checks
> >>>> - Load json File from Gateway if Gateway in Batman in Range
> >>>>
> >>>> Update in v6:
> >>>> !!UNTESTED!!
> >>>> - fix hidden station v6
> >>>> - fix -n to -f if
> >>>> - Add function to check for a gateway and use this
> >>>> - remove /etc/community.cfg and variables
> >>>> - send fewer infos to keyxchangev2
> >>>> - add a check if /tmp/keyxchangev2 not downloadable and edit a bit
> >>>> on the wgets
> >>>> - change the position from json_load and do this only 1 times
> >>>>
> >>>> Update in v7:
> >>>> !!UNTESTED!!
> >>>> - delete keyxchangev2data at start of the script
> >>>> - do only things with keyxchangev2data if available
> >>>> - change keyxchangev2 url
> >>>>
> >>>> Update in v8/v9:
> >>>> - rebase onto 20170918-beta
> >>>>
> >>>> Update in v10:
> >>>> - Minor code fixes
> >>>> - Added fff-hoods to fff-base Makefile
> >>>> - Removed trailing whitespaces and harmonized tabs
> >>>> - Fixed some comments spelling
> >>>> - Added mac for hostname rewrite
> >>>> - Removed redundant check for /tmp/keyxchangev2data
> >>>>
> >>>> Update in v11:
> >>>> - Changed isGatewayAvailable to return integers (bool is
> >>>> not valid) and removed brackets for evaluations
> >>>> - Added variables for channels as they are used twice
> >>>> - Fixed $radio not set at the beginning (WORKAROUND!)
> >>>> - Changed OpenWRT to LEDE
> >>>> - Correctly reset json_select before reuse
> >>>> - Some tidying-up of comments and quotes
> >>>> - Fixed vpn loop so it works for more than one host (TESTED)
> >>>> - Fixed "else" if no file received
> >>>>
> >>>> Changes in v12:
> >>>> - Removed obsolete hostname
> >>>>
> >>>> Changes in v14 (Tested, working Inet+mesh):
> >>>> - Fixed stderr redirect
> >>>> - Added call of configurehood to rc.local, so it is triggered
> >>>> if wan does not come up. To prevent race condition,
> >>>> hotplug.d is removed.
> >>>> - Added wifi call to configAP setup
> >>>> - Remove hiddenap flag after successful setup
> >>>> - Added -q to uci calls
> >>>> - Added network interface configSta
> >>>> - Substitute timestamp to enable SHA comparison
> >>>> - Removed started-check from vpn-select
> >>>>
> >>>> Changes in v15:
> >>>> - Fixed 5 GHz channel
> >>>> - Only start vpn-select if router has internet
> >>>> - Put ping into function since it is used twice
> >>>> - Check for started in micrond to prevent race condition
> >>>> - Moved copy of keyxchangev2data to the end
> >>>>
> >>>> Changes in v16:
> >>>> - Open configap for both 2.4 and 5 GHz
> >>>> ---
> >>>> bsp/default/root_file_system/etc/rc.local | 4 +
> >>>> src/packages/fff/fff-hoods/Makefile | 39 ++++
> >>>> .../fff/fff-hoods/files/usr/lib/micron.d/fff-hoods | 1 +
> >>>> .../fff/fff-hoods/files/usr/sbin/configurehood | 230
> +++++++++++++++++++++
> >>>> .../fff/fff-vpn-select/files/usr/sbin/vpn-select | 2 -
> >>>> src/packages/fff/fff/Makefile | 3 +-
> >>>> 6 files changed, 276 insertions(+), 3 deletions(-) create mode
> >>>> 100644 src/packages/fff/fff-hoods/Makefile
> >>>> create mode 100644
> >>>> src/packages/fff/fff-hoods/files/usr/lib/micron.d/fff-hoods
> >>>> create mode 100755
> >>>> src/packages/fff/fff-hoods/files/usr/sbin/configurehood
> >>>>
> >>>> diff --git a/bsp/default/root_file_system/etc/rc.local
> >>>> b/bsp/default/root_file_system/etc/rc.local
> >>>> index bd972fb..59042c3 100755
> >>>> --- a/bsp/default/root_file_system/etc/rc.local
> >>>> +++ b/bsp/default/root_file_system/etc/rc.local
> >>>> @@ -4,6 +4,10 @@
> >>>>
> >>>> /usr/sbin/configurenetwork
> >>>>
> >>>> +sleep 3
> >>>> +
> >>>> +/usr/sbin/configurehood
> >>>> +
> >>>> touch /tmp/started
> >>>>
> >>>> exit 0
> >>>> diff --git a/src/packages/fff/fff-hoods/Makefile
> >>>> b/src/packages/fff/fff-hoods/Makefile
> >>>> new file mode 100644
> >>>> index 0000000..f85178d
> >>>> --- /dev/null
> >>>> +++ b/src/packages/fff/fff-hoods/Makefile
> >>>> @@ -0,0 +1,39 @@
> >>>> +include $(TOPDIR)/rules.mk
> >>>> +
> >>>> +PKG_NAME:=fff-hoods
> >>>> +PKG_VERSION:=0.0.1
> >>>> +PKG_RELEASE:=1
> >>>> +
> >>>> +PKG_BUILD_DIR:=$(BUILD_DIR)/fff-hoods
> >>>> +
> >>>> +include $(INCLUDE_DIR)/package.mk
> >>>> +
> >>>> +define Package/fff-hoods
> >>>> + SECTION:=base
> >>>> + CATEGORY:=Freifunk
> >>>> + TITLE:= Freifunk-Franken hoods
> >>>> + URL:=http://www.freifunk-franken.de
> >>>> + DEPENDS:=+fff-network
> >>>> +endef
> >>>> +
> >>>> +define Package/fff-hoods/description
> >>>> + This package load and configures the current hood endef
> >>>> +
> >>>> +define Build/Prepare
> >>>> + echo "all: " > $(PKG_BUILD_DIR)/Makefile endef
> >>>> +
> >>>> +define Build/Configure
> >>>> + # nothing
> >>>> +endef
> >>>> +
> >>>> +define Build/Compile
> >>>> + # nothing
> >>>> +endef
> >>>> +
> >>>> +define Package/fff-hoods/install
> >>>> + $(CP) ./files/* $(1)/
> >>>> +endef
> >>>> +
> >>>> +$(eval $(call BuildPackage,fff-hoods))
> >>>> diff --git
> >>>> a/src/packages/fff/fff-hoods/files/usr/lib/micron.d/fff-hoods
> >>>> b/src/packages/fff/fff-hoods/files/usr/lib/micron.d/fff-hoods
> >>>> new file mode 100644
> >>>> index 0000000..39e800e
> >>>> --- /dev/null
> >>>> +++ b/src/packages/fff/fff-hoods/files/usr/lib/micron.d/fff-hoods
> >>>> @@ -0,0 +1 @@
> >>>> +*/5 * * * * [ -f /tmp/started ] && /usr/sbin/configurehood
> >>>> diff --git
> >>>> a/src/packages/fff/fff-hoods/files/usr/sbin/configurehood
> >>>> b/src/packages/fff/fff-hoods/files/usr/sbin/configurehood
> >>>> new file mode 100755
> >>>> index 0000000..ab6bd53
> >>>> --- /dev/null
> >>>> +++ b/src/packages/fff/fff-hoods/files/usr/sbin/configurehood
> >>>> @@ -0,0 +1,230 @@
> >>>> +#!/bin/sh
> >>>> +
> >>>> +. /usr/share/libubox/jshn.sh
> >>>> +. /lib/functions/fff/wireless
> >>>> +
> >>>> +rm /tmp/keyxchangev2data
> >>>> +
> >>>> +# Gatewaycheck function
> >>>> +isGatewayAvailable() {
> >>>> + if [ "$(batctl gwl | wc -l)" -gt 2 ]; then
> >>>> + return 0
> >>>> + else
> >>>> + return 1
> >>>> + fi
> >>>> +}
> >>>> +
> >>>> +# Ping test
> >>>> +hasInternet() {
> >>>> + test_ipv4_host1="keyserver.freifunk-franken.de" # Freifunk-
> Franken keyserver
> >>>> + test_ipv4_host2="8.8.8.8" # Google DNS
> >>>> + test_ipv6_host1="heise.de" # heise Zeitschriftenverlag
> >>>> + if ping -w5 -c3 "$test_ipv4_host1" &>/dev/null ||
> >>>> + ping -w5 -c3 "$test_ipv4_host2" &>/dev/null ||
> >>>> + ping6 -w5 -c3 "$test_ipv6_host1" &>/dev/null ; then
> >>>> + return 0
> >>>> + fi
> >>>> + return 1
> >>>> +}
> >>>> +
> >>>> +chan2ghz="1"
> >>>> +chan5ghz="36"
> >>>> +
> >>>> +# Hidden AP check
> >>>> +
> >>>> +if [ -f /tmp/hiddenapflag ]; then
> >>>> + if isGatewayAvailable ; then
> >>>> +
> >>>> + uci set network.configap=interface
> >>>> + uci set network.configap.proto='static'
> >>>> + uci set network.configap.ip6addr='fe80::1/64'
> >>>> + uci commit network
> >>>> +
> >>>> + for radio in $(uci show wireless | sed -n 's,.*\.\([a-z0-
> 9]*\)=wifi-device,\1,p'); do
> >>>> + if ! wifiAddAP "$radio" "config.franken.freifunk.net"
> "configap" "configap" "1"; then
> >>>> + echo "Can't add Config interface on $radio."
> >>>> + exit 1
> >>>> + fi
> >>>> + done
> >>
> >> ich bekomm die fe80::1 nicht ans wXconfigap gehangen:
> >>
> >> w2configap Link encap:Ethernet HWaddr 56:C7:BF:3B:3C:3E
> >> inet6 addr: fe80::54c7:bfff:fe3b:3c3e/64 Scope:Link
> >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> >> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> >> TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
> >> collisions:0 txqueuelen:1000
> >> RX bytes:0 (0.0 B) TX bytes:432 (432.0 B)
> >>
> >> [...]
> >>
> >> w5configap Link encap:Ethernet HWaddr 56:C7:BF:3B:3C:3D
> >> inet6 addr: fe80::54c7:bfff:fe3b:3c3d/64 Scope:Link
> >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> >> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> >> TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
> >> collisions:0 txqueuelen:1000
> >> RX bytes:0 (0.0 B) TX bytes:728 (728.0 B)
> >>
> >> root at c25testknoten:/tmp# uci show etwork.configap.ip6addr
> >> uci: Entry not found
> >> root at c25testknoten:/tmp# uci show network.configap.ip6addr
> >> network.configap.ip6addr='fe80::1/64'
> >> root at c25testknoten:/tmp# cat /etc/config/wireless
> >>
> >> [...]
> >>
> >> config wifi-iface 'w2configap'
> >> option device 'radio1'
> >> option network 'configap'
> >> option ifname 'w2configap'
> >> option mode 'ap'
> >> option ssid 'config.franken.freifunk.net'
> >> option encryption 'none'
> >> option hidden '1'
> >>
> >> config wifi-iface 'w5configap'
> >> option device 'radio0'
> >> option network 'configap'
> >> option ifname 'w5configap'
> >> option mode 'ap'
> >> option ssid 'config.franken.freifunk.net'
> >> option encryption 'none'
> >> option hidden '1'
> >>
> >>
> >> weiß gerade nicht warum aber irgendwas hakt da noch. Eingespielt ist
> >> folgende Patchreihe:
> >>
> >> 527 523 528 525 524 526 531 532 535 545 546 550 551 555 556
> >>
> >> mfg
> >>
> >> Christian
> >>
> >>
> >>>> +
> >>>> + wifi
> >>>> + fi
> >>>> + rm /tmp/hiddenapflag
> >>>> +fi
> >>>> +
> >>>> +lat=$(uci -q get system. at system[0].latitude) long=$(uci -q get
> >>>> +system. at system[0].longitude)
> >>>> +
> >>>> +# if we have Internet, we download the Hoodfile from the
> >>>> +keyxchangev2 if hasInternet ; then
> >>>> + wget -T15 -t5 "http://keyserver.freifunk-
> franken.de/v2/?lat=$lat&long=$long" -O /tmp/keyxchangev2data
> >>>> + #if no Internet, we connect to the hidden AP and download the
> >>>> +file from another Node in range else
> >>>> + # connect to wireless hidden ap here and download the json File
> from the nearest router
> >>>> + # Only do that, when we have no gateway in range. If the
> Uplinkrouter changed the hood, we lost the GW and do this automatically
> again, I think! Nice idea?
> >>>> + if ! isGatewayAvailable ; then
> >>>> + #now we haven't a gateway in Range, we search for a hidden
> AP to get a keyxchangev2data file!
> >>>> + #first we delete all wifi settings
> >>>> + if ! wifiDelAll; then
> >>>> + echo "Can't delete current wifi setup"
> >>>> + exit 1
> >>>> + fi
> >>>> + #now we look for phy and add this
> >>>> + for phy in $(iw phy | awk '/^Wiphy/{ print $2 }'); do
> >>>> + if iw phy "$phy" info | grep -q -m1 "2... MHz"; then
> >>>> + echo "$phy is 2.4 GHz"
> >>>> + radio="$(wifiAddPhy "$phy" "$chan2ghz")"
> >>>> + if [ -z "$radio" ]; then
> >>>> + echo "Can't create radio for $phy"
> >>>> + exit 1
> >>>> + fi
> >>>> + fi
> >>>> + if iw phy "$phy" info | grep -q -m1 "5... MHz"; then
> >>>> + echo "$phy is 5 GHz"
> >>>> + radio="$(wifiAddPhy "$phy" "$chan5ghz")"
> >>>> + if [ -z "$radio" ]; then
> >>>> + echo "Can't create radio for $phy"
> >>>> + exit 1
> >>>> + fi
> >>>> + fi
> >>>> + #and here we add the station
> >>>> + if ! wifiAddSta "$radio" "config.franken.freifunk.net"
> "configSta"; then
> >>>> + echo "Can't add Sta interface on $radio."
> >>>> + exit 1
> >>>> + else
> >>>> + uci -q set network.configSta=interface
> >>>> + uci -q set network.configSta.proto='static'
> >>>> + uci -q commit network
> >>>> + fi
> >>>> + done
> >>>> +
> >>>> + wifi
> >>>> + # wait a moment to start the interface
> >>>> + sleep 10;
> >>>> + # and here we can download the Hoodfile from the other
> node
> >>>> + wget -T15 -t5 "http://[fe80::1%w2sta]/keyxchangev2data" -O
> /tmp/keyxchangev2data
> >>>> + else
> >>>> + echo "We have a Gateway in Range, we load the
> keyxchangev2data from fe80::1"
> >>>> + wget -T15 -t5 "http://[fe80::1%br-mesh]/keyxchangev2data"
> -O /tmp/keyxchangev2data
> >>>> + fi
> >>>> +fi
> >>>> +
> >>>> +if [ -s /tmp/keyxchangev2data ]; then
> >>>> +
> >>>> + # we get a json file in this format:
> >>>> + # https://pw.freifunk-franken.de/patch/205/
> >>>> + # but without signature, every hood file we get is valid!
> >>>> +
> >>>> + catnew="$(cat /tmp/keyxchangev2data | sed 's/"timestamp":[0-
> 9]*/"timestamp":0/')"
> >>>> + catold="$(cat /www/public/keyxchangev2data 2>/dev/null | sed
> 's/"timestamp":[0-9]*/"timestamp":0/')"
> >>>> + sumnew=$(echo "$catnew" | sha256sum | cut -f1 -d " ")
> >>>> + sumold=$(echo "$catold" | sha256sum | cut -f1 -d " ")
> >>>> +
> >>>> + json_load "$(cat /tmp/keyxchangev2data)"
> >>>> +
> >>>> + if [ "$sumnew" != "$sumold" ]; then
> >>>> + echo "New file detect, we reconfigure the Node";
> >>>> +
> >>>> + json_select hood
> >>>> +
> >>>> + json_get_var hood name
> >>>> + json_get_var mesh_bssid mesh_bssid
> >>>> + json_get_var mesh_essid mesh_essid
> >>>> + json_get_var essid essid
> >>>> + # i think the next things we don't active this in the first
> version! we can do it later
> >>>> + #json_get_var channel2 channel2
> >>>> + #json_get_var mode2 mode2
> >>>> + #json_get_var type2 type2
> >>>> + #json_get_var channel5 channel5
> >>>> + #json_get_var mode5 mode5
> >>>> + #json_get_var type5 type5
> >>>> + #json_get_var protocol protocol
> >>>> +
> >>>> + json_select ".." # back to root
> >>>> +
> >>>> + echo "Setting hood name: $hood"
> >>>> + uci set "system. at system[0].hood=$hood"
> >>>> +
> >>>> + if ! wifiDelAll; then
> >>>> + echo "Can't delete current wifi setup"
> >>>> + exit 1
> >>>> + fi
> >>>> +
> >>>> + for phy in $(iw phy | awk '/^Wiphy/{ print $2 }'); do
> >>>> + if iw phy "$phy" info | grep -q -m1 "2... MHz"; then
> >>>> + echo "$phy is 2.4 GHz"
> >>>> + radio="$(wifiAddPhy "$phy" "$chan2ghz")"
> >>>> + if [ -z "$radio" ]; then
> >>>> + echo "Can't create radio for $phy"
> >>>> + exit 1
> >>>> + fi
> >>>> + fi
> >>>> + if iw phy "$phy" info | grep -q -m1 "5... MHz"; then
> >>>> + echo "$phy is 5 GHz"
> >>>> + radio="$(wifiAddPhy "$phy" "$chan5ghz")"
> >>>> + if [ -z "$radio" ]; then
> >>>> + echo "Can't create radio for $phy"
> >>>> + exit 1
> >>>> + fi
> >>>> + fi
> >>>> +
> >>>> + if ! wifiAddAP "$radio" "$essid" "mesh" "ap" "0"; then
> >>>> + echo "Can't add AP interface on $radio."
> >>>> + exit 1
> >>>> + fi
> >>>> +
> >>>> + # here we set a bit for add hidden AP
> >>>> + touch /tmp/hiddenapflag
> >>>> +
> >>>> + if ! wifiAddAdHocMesh "$radio" "$mesh_essid"
> "$mesh_bssid"; then
> >>>> + echo "Can't add AP interface on $radio."
> >>>> + exit 1
> >>>> + fi
> >>>> + done
> >>>> +
> >>>> + echo "Loading wifi"
> >>>> + wifi
> >>>> +
> >>>> + # copy the file to webroot so that other Meshrouter can
> download it;
> >>>> + # copy only after all other steps so IF can be reentered if
> something goes wrong
> >>>> + cp /tmp/keyxchangev2data /www/public/
> >>>> +
> >>>> + else
> >>>> + echo "We have no new file. We do nothing. We try it again in
> 5 minutes...";
> >>>> + exit 0
> >>>
> >>> warum dieses exit? Ich hatte eben den Fall das ich hier gelandet bin
> >>> aber noch kein VPN aufgebaut war. Dadurch kam ich dann weiter unten
> >>> nicht mehr dazu die /usr/sbin/vpn-select aufzurufen und dadurch
> >>> blieb der Router ohne VPN (es handelt sich um einen Uplinkrouter)
> >>>
> >>> nachdem ich dieses exit 0 rausgenommen habe tut es...
> >>>
> >>> Wie ich genau in diese Situation gekommen bin weiß ich nicht,
> >>> vermute aber durch einen einfachen reboot oder evtl. auch durch ein
> >>> Gatewayneustart das ich zur gleichen Zeit durchgeführt habe.
> >>>
> >>> mfg
> >>>
> >>> Christian
> >>>
> >>>> + fi
> >>>> +
> >>>> + # and now we read the VPN Data and give this data to fff-vpn
> >>>> + json_select vpn
> >>>> + Index=1
> >>>> + rm /tmp/fastd_fff_output
> >>>> + touch /tmp/fastd_fff_output
> >>>> + while json_select "$Index" > /dev/null
> >>>> + do
> >>>> + json_get_var protocol protocol
> >>>> + if [ "$protocol" == "fastd" ]; then
> >>>> + json_get_var servername name
> >>>> + echo "####${servername}.conf" >>
> /tmp/fastd_fff_output
> >>>> + echo "#name \"${servername}\";" >>
> /tmp/fastd_fff_output
> >>>> + json_get_var key key
> >>>> + echo "key \"${key}\";" >> /tmp/fastd_fff_output
> >>>> + json_get_var address address
> >>>> + json_get_var port port
> >>>> + echo "remote ipv4 \"${address}\" port $port float;"
> >> /tmp/fastd_fff_output
> >>>> + fi
> >>>> + echo "" >> /tmp/fastd_fff_output
> >>>> + json_select ".." # back to vpn
> >>>> + Index=$(( Index + 1 ))
> >>>> + done
> >>>> + echo "###" >> /tmp/fastd_fff_output
> >>>> + json_select ".." # back to root
> >>>> + #this we do every 5 minutes, because it can change the VPN Protocol
> >>>> + #and now we get to vpn-select Script and load VPNs
> >>>> +
> >>>> + if hasInternet ; then
> >>>> + sh /usr/sbin/vpn-select
> >>>> + fi
> >>>> +else
> >>>> + echo "We haven't got a file. We do nothing. We try it again in 5
> minutes...";
> >>>> + exit 0
> >>>> +fi
> >>>> diff --git
> >>>> a/src/packages/fff/fff-vpn-select/files/usr/sbin/vpn-select
> >>>> b/src/packages/fff/fff-vpn-select/files/usr/sbin/vpn-select
> >>>> index bb4c933..bbc87cc 100755
> >>>> --- a/src/packages/fff/fff-vpn-select/files/usr/sbin/vpn-select
> >>>> +++ b/src/packages/fff/fff-vpn-select/files/usr/sbin/vpn-select
> >>>> @@ -1,7 +1,5 @@
> >>>> #!/bin/sh
> >>>>
> >>>> -test -f /tmp/started || exit
> >>>> -
> >>>> make_config() {
> >>>> # remove old config
> >>>> >/etc/config/tunneldigger
> >>>> diff --git a/src/packages/fff/fff/Makefile
> >>>> b/src/packages/fff/fff/Makefile index 166d423..305ab8d 100644
> >>>> --- a/src/packages/fff/fff/Makefile
> >>>> +++ b/src/packages/fff/fff/Makefile
> >>>> @@ -29,7 +29,8 @@ define Package/fff-base
> >>>> +fff-wireless \
> >>>> +fff-timeserver \
> >>>> +fff-vpn-select \
> >>>> - +simple-tc
> >>>> + +simple-tc \
> >>>> + +fff-hoods
> >>>> endef
> >>>>
> >>>> define Package/fff-base/description
> >>>>
> >>
> >>
> >>
> >
> >
> >
Mehr Informationen über die Mailingliste franken-dev